Advertisement
OPERATION
The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result i
in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or
J
performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety
mask over spectacles.
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED
The engine speed was set at the factory for optimum per-
formance. Speed is not adjustable.
ENGINE
ZONE
CONTROL
&
CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the risk
of blade contact injury. Do not under
any circumstances
attempt to defeat
the function of the operator control.
The blade turns when the engine is
running.
Your lawn mower isequipped with an operator presence
control bar which requires the operator to be positioned
behind the lawn mower handle to start and operate the
lawn mower.
DRIVE
CONTROL
(See Fig. 5)
•
Self-propelling is controlled by holding the operator
presence control bar down to the handle and pulling
the drive control lever rearward to the handle. The
farther toward the handle the lever is pulled, the faster
the unit will travel.
•
Forward motion will stop when either the operator pres-
ence control bar or drive control lever are released. To
stop forward motion without stopping engine, release
the drive control lever only. Hold operator presence
control bar down against handle to continue mowing
without self-propelling.
NOTE: If after releasing the drive control the mower will
not roll backwards, push the mower forward slightly to
disengage drive wheels.
OPERATOR PRESENCE CONTROL BAR
DRIVE
CONTROL
LEVER
ADJUSTMENT
TO ENGAGE
DRIVE
BUTTON (ON
DRIVE
CONTROL
UNDERSIDE)
CONTROL
DISENGAGED
FIG. 5
DRIVE
CONTROL
ADJUSTMENT
(See Fig. 5)
Over time, the drive control system may become "loose",
resulting in decreased speed. There is a button on the
underside of the drive control housing to increase tension
on the drive cable. Proceed as follows:
1. Turn unit off and disconnect spark plug wire from plug.
2.
Pull out button on underside of drive control then push
it back in.
3.
Operate mower to see if drive speed has increased. If
there is no increase, the drive belt is worn and needs
to be replaced.
TO ADJUST
CUTTING
HEIGHT
(See Fig
6)
Both rear wheels are adjusted by a single lever on the left
rear wheel.
•
Pull adjuster lever toward wheel.To raise mower, move
lever forward to desired position .To lower mower, move
the lever toward the rear.
NOTE: There are seven (7) height adjustment positions
for the rear wheels.
Both front wheels are adjusted as follows:
1.
Remove wheel boll and hardware and reassemble in
desired adjustment hole.
2.
Reinstall wheel components in the same order as they
were before removal. Tighten securely.
NOTE: There are seven (7) height adjustment holes for the
front wheels. Be sure both front wheels are in the same hole.
IMPORTANT: BE SURE TO ADJUST BOTH FRONT AND REAR
WHEELS TO THE SAME HEIGHT.
LEVER
BACKWARD
TO LOWER REAR
OF MOWER
LEVER
FORWARD
TO RAISE
REAR
OF MOWER
LOCKBAR "FREE-
WHEEL" POSITION
7
O-RING _R
BOLT
LOCKBAR
WING NU]
("LOCKED"
POSITION)
FIG. 6
CASTER WHEEL OPERATION
(See Fig. 6)
The front wheels can be "locked" into position or set to
"freewheel" for better maneuverability. Placing the Iockbars
in the outer holes of the adjustment brackets "locks" the
front wheels. Likewise, placing the lockbars in the inner
holes of the adjustment brackets allows the front wheels
to spin freely (ffreewheeF).
•
Lift Iockbar until the frontmost end clears the adjust-
ment bracket, then pivot lockbar to desired position.
IMPORTANT:FRONT WHEELS MUST BE "LOCKED" INTO
POSITIONWHEN OPERATINGON A SLOPE.MOW ACROSS
THE FACEOF SLOPES:NEVER UP AND DOWN.
Advertisement
