Tool Agitator Brush Roll ...... Replacing Power Hand Tool Belt ..13 Replacing Headlight ......Thermal Protector ......Warranty ..........Parts & accessories mail reorder form ..........Review this manual before operating cleaner. Lire attentivement instructions hoover.com avant d'utiliser I'appareil. hoover.ca...
Page 2
Hoover Sales and Service Center or Authorized Hoover Warranty Service Dealer (Depot). • Do not pull or carry...
If you need any assistance: Visit our website at hoover.com. Click on the "Service" button to find the service outlet nearest you Call 1-800-944-9200 for an automated referral of authorized service outlet locations (U,S, only) OR Call 1-330-499-9499 to speak with a representative...
Page 4
Align end of hose with projections Position hose over rack (C) and into (A) over slots on dirt duct (B), hose tube (D), Slide hose into slots and twist hose NOTE: Hose must be connected at to lock it into place (To detach hose, the hose tube (D) and at the dirt reverse procedure), duct (B) on the back of the cleaner...
Page 6
Cord rewind Telescoping handle Transporting cleaner Grasp the end of the plug and pull To move your cleaner from room to The telescoping handle includes to release cord from cord reel, After room, put handle in upright position, adjustable settings to various tilt cleaner back on rear wheels and desired cord length is reached, the heights for user comfort.
Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas, The cleaner is ready for tool use when handle is in upright position, The agitator brush roll will not rotate when the cleaner is in the upright position or the if the agi- Cleaning lightweight...
Page 8
Extra Reach TM hose vJ_;| • (available at additional cost) The Extra Reach hose provides easier cleaning of stairs and hard to reach places, Follow the steps below for attaching and detaching the Extra Reach hose, Attach wand tools Align end of hose with projections (D) over slots (E) on Extra Reach Attach tool or wand to the hose (F), hose, Slide hose into slots and twist...
What to buy When purchasing a new secondary filter cartridge, ask for HOOVER part No. 93002517. To purchase a new black foam filter, ask for Remove dirt cup as described HOOVER part No. 93002518.
Page 10
Replace belt if it is stretched, cut or broken, What to buy To assure effective operation, use only genuine HOOVER belts with }/our cleaner, When purchasing a new belt, ask for Flat belt - HOOVER part No. 40201-271,...
Page 11
When purchasing a new agitator, edge of a card across bottom plate Disconnect cleaner from electrical ask for HOOVER part No. while turning agitator brush roll, To outlet. 93002361. maintain cleaning effectiveness, Turn carpet height adjustment knob...
Page 12
When agitator brushes are worn, the brush roll should be replaced, Ask for HOOVER part No. 48414-088. 2, Unscrew the two Phillips screws 3, Remove agitator including and remove belt guard (B), plates (C) and discard, 4, Inspect belt to ensure that it is in...
Page 13
Replace belt When replacing belt, ask for Belt replacement HOOVER part No. 38528-037. Inspect the belt The powered hand tool belt is designed to last a long time and is not normally replaced, However, if the belt is cracked, gouged or bro-...
Lubrication Do not send your cleaner to Hoover in North Canton, Ohio for service, The motor is equipped with bear- this will only result in delay, Possible Cause ings that contain sufficient lubrica- Possible Solution tion for the life of the motor, The...
12, Disconnect powered hand tool delivery, or house calls; however, i[ you from hose. Remove bottom plate, mail your appliance to a Hoover Sales belt guard and turbine as described and Service Center for warranty service, in Figs, 3-24, 3-25 and 3-31,...
Need help?
Do you have a question about the U5194-900 and is the answer not in the manual?
Questions and answers