Burner Grates; Burner Head And; Cap Replacement - GE JGP970 Owner's Manual

www.GEAppliances.com
f %
Burnercapproperlyseated
Burner cap not properly seated
Burner Head and Cap Replacement
Replace the burner head onto the
burner base, making sure that the head is
properly oriented over the burner base
and the electrode, Make sure to place the
coFi'ect btlFner
head
on the coFi'ect
burner base and that the bm'ner head sits
level on the burner base. The burner
heads are not interchangeable,
Replace the bm'ner cap onto the bm'ner
head, making sure to place the correct
burner cap on the correct bm'ner head.
The burner caps are not interchangeable.
Also, make sm'e that the burner caps are
properly seated on the burner heads.
JGP940 and JGP970 (aft burners)
JGP933 and JGP963
(right front burner only)
Burner cap
Burner head
Pin __Burner
indentations base
Make sure the pflTsf17 the burner heads match
the burner base flTdentafionsand that they are
properly seated h7them by rotating the heads
until they are level
JGP328,JGP330,JGP628,JGP630,
JGP933,JGP945,JGP963,JGP975
Stability Burnerbead _,_ / / J
chamber " -'-'-'-__
1
_ Electrode
Burner b ase
Make surethe slot in the burner headis positioned
over the electrode. The burner cap has three
to four pflTs.When replacing the cap, make sure
none of the pflTssits in the stability chambe_
JGP945and JGP975
(rightfront burner only)
Burner cap
Cb
Burner h ead /_
assemblyk_) Orifice
Electrode base
Make sure the hole f17the burner head assembly
is positioned over the electrode and that the burner
head is fully inserted flTside the burner base. A
small gap between the base and head is normal
Burner Grates
(Onsomemodels)
"OUTSIDE .... INSIDE .... OUTSIDE"
edge edges edge
(Onsome models)
"INSIDE"
"OUTSIDE" edge _ "OUTSIDE" edge
Tabs
34mr cooktop
has professional sb'le
grates. These grates a_e designed tot
specific positions. These grates should
only be used in their proper positions;
they should not be interchanged. For
yore" convenience, the undersides ot
the left and right grates are marked
"OUTSIDE" and "INSIDE". Make sure
that the sides marked "OUTSIDE" a_e
fi_dng the outer edge of the cooktop and
the sides marked "INSIDE" are
fi_dng each other: All grates
should touch once they are
fiflly assembled on the
cooktop StllS[ilce.
For cooktops with three grates,
make sure that the tabs on
either side of the center grate
fit into the slots located on the
"INSIDE" edge ot the side
grates.
I,ift the bm'ner grates out only when
cool. Grates should be washed regularly
and, of cotlrse, after spillove_s. Wash
them in the dishwasher or in hot, soapy
water and _inse with clean water: _,_]_en
replacing the grates, be sure they are
positioned securely over the burne_.
Although they are din'able, the grates will
gradually lose their shine, regardless of
the best care you can give them. This is
due to their continual exposure to high
temperatures. Ybu will notice this sooner
with lighter color grates.
Do not operate a bm'ner for an extended
period of time without cookware on the
grate. The finish on the grate may chip
without cookware
to absorb the heat.
NOTE: Donot clean the grates in a
self-cleaning oven.
11