GE JGP628 Installation Instructions Manual

36" sealed gas cooktop
Hide thumbs Also See for JGP628:

Advertisement

Available languages

Available languages

Installation
Instructions
36" Sealed Gas Cooktop
JGP628,
JGP630,
JGP963, JGP970,
JGP975,
ZGU36
=_ Questions?
Call 800.GE.CARES
(800.432.2737)
or Visit our Website
at: ge.com
In Canada,
call 1.800.561.3344
or Visit our Website
at: www.geappliances.ca
I
IN THE COMMONWEALTH
OF
MASSACHUSETTS:
• This product
must be installed
by a
licensed
plumber
or gas fitter.
• When
using ball-type
gas shut-off
valves,
they shall be the T-handle
type.
• A flexible
gas connector,
when
used, must
not exceed 3 feet.
BEFORE YOU BEGIN
Read these
instructions
completely
and carefully.
• IMPORTANT
- Save t hese
instructions
for local
inspector's
use.
• IMPORTANT
- Observe all
governing
codes
and ordinances.
• Note to Installer-
Be sure to leave these
instructions
with
the Consumer.
• Note to Consumer-
Keep these
instructions
for future
reference.
• Product
failure
due to improper
installation
is not covered
under
the Warranty.
_kWARNING - This
appliance
must
be properly
grounded.
IMPORTANT
-
Leak testing
of the
appliance
shall
be conducted
according
to
the manufacturer's
instructions.
• Proper installation
is the responsibility
of the installer
and product
failure due to
improper
installation
is NOT covered
under
warranty.
_4, WARNING - Disconnect
all
electrical
power
at the main
circuit
breaker
or fuse box before
installing.
FOR YOUR SAFETY:
-_ WARNING - Iftheinformation
in this manual
is not followed
exactly,
a fire,
explosion
or gas leak may result causing
property
damage,
personal
injury or death.
Do not store or use gasoline
or other
flammable
vapors
and liquids in the vicinity
of this or any other
appliance!
WHAT TO DO IF YOU
SMELL GAS:
Do not try to light
any appliance.
Do not
touch
any electrical
switch;
do not use any
phone
in your
building.
Immediately
call your
gas supplier
from
a
neighbor's
phone.
Follow
the gas supplier's
instructions.
• If you cannot
reach your
gas supplier,
call
the fire department.
Installation
and service
must
be performed
by
a qualified
installer,
service
agency
or the gas
supplier.
This cooktop
has been design
certified
by CSA International.
You'll
find safety
precautions
in your
Owner's
Manual.
Read them
carefully.
Installation
of this cooktop
must
conform
with
local codes
or, in the absence
of local
codes with
the National
Fuel Gas Code,
ANSI
Z223.1/NFPA
54-Latest
edition.
Be sure your
cooktop
is installed
properly
by a qualified
installer
or service
technician.
To eliminate
reaching
over surface
burners,
cabinet
storage
above
burner
should
be
avoided.
• Do not install
the unit near an outside
door
or where
a draft
may affect
its use.
31-10612-3
(11-08 JR)
1

Advertisement

Table of Contents
loading

Summary of Contents for GE JGP628

  • Page 1 Installation 36" Sealed Gas Cooktop Instructions JGP628, JGP630, JGP963, JGP970, JGP975, ZGU36 =_ Questions? In Canada, Call 800.GE.CARES call 1.800.561.3344 or Visit our Website (800.432.2737) or Visit our Website at: www.geappliances.ca at: ge.com IN THE COMMONWEALTH FOR YOUR SAFETY: MASSACHUSETTS: -_ WARNING - Iftheinformation •...
  • Page 2: Important Safety Instructions

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL REQUIREMENTS PARTS INCLUDED This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse 2 Screws Foam Tape 2 Hold having amperage...
  • Page 3: Pre-Installation

    Installation Instructions PRE-INSTALLATION CHECKLIST Remove Installation Instructions from When preparing cooktop opening, make sure the inside of the cabinet literature pack and read them carefully the cooktop do not interfere with each before you begin. other. (See section on preparing Be sure to place all literature, Use and...
  • Page 4: Preparing The Opening

    Installation Instructions PREPARING THE OPENING 17-1MAINTAIN THE FOLLOWING RECOMMENDED GAS SUPPLY MINIMUM CLEARANCE LOCATION FROM BACKWALL DIMENSIONS 1" Min. From Backwall 13" MAX. Depth of unprotected overhead cabinets 6" MIN. clearance from Recommended cutout to side wall on gas supply the right of the unit location From Cutout...
  • Page 5: Installing The Cooktop Unit

    Installation Instructions INSTALLING THE COOKTOP UNIT LOCATE ELECTRICAL OUTLET LOCATE MOUNTING PARTS AND GAS SHUT-OFF VALVE Remove the hold down brackets from BENEATH CABINET literature package. NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS UNIT. _Shut-Off II Outlet 12" Valve _I_ Below ATTACH BRACKETS TO Countertop...
  • Page 6 Installation Instructions INSTALLATION--GAS CONNECTIONS ITI PROVIDE ADEQUATE INSTALL REGULATOR ONTO GAS SUPPLY BURNER BOX BOTTOM This cooktop is designed to operate Screw natural gas at 4" of water column manifold regulator onto pressure and 7" of water column (W.C.) the burner supply pressure.
  • Page 7: Check For Leaks

    Installation Instructions CHECK FOR LEAKS INSTALLATION OVER BUILT-IN OVEN Before testing for leaks, make sure all burner knobs are in the OFF position. See built-in oven installation for complete installation instructions. After connecting the cooktop to gas, check system for leaks with a manometer.
  • Page 8 Installation Instructions INSTALLATIONmE LECTRICAL CONNECTIONS WARNING - Disconnect _-I ELECTRICAL SUPPLY AND OUTLET electrical power at the main circuit breaker or fuse box before installing. An adequate electrical supply and outlet must be used to operate the electrical parts of your cooktop.
  • Page 9 Installation Instructions .4,CAUTION: USAGE SITUATIONS WHERE Attaching the adaptor APPLIANCE POWER CORD ground terminal to the wall receptacle cover WILL BE DISCONNECTED screw does not ground the appliance unless the screw is metal, and not insulated, and the INFREQUENTLY wall receptacle is grounded through the house...
  • Page 10: Cooktop Burners

    Installation Instructions COOKTOP BURNERS r-cq Make sure the Burner cap ASSEMBLING THE COOKTOP pins in the burner BURNERS heads match the The electrode of the spark igniter is exposed. burner base Be careful not to push any cooktop controls Burner head indentations while...
  • Page 11 Installation Instructions CHECK IGNITERS THE BURNER FLAMES Operation of the electric igniters should be Turn each burner on. Flames should be blue checked after the cooktop and supply line in color with no trace of yellow. The burner have been carefully checked for leaks and flames...
  • Page 12: Operation Checklist

    Installation Instructions OPERATION CHECKLIST Make sure all controls are left in the OFF When ordering parts, always include position. Check to be sure the cooktop serial number, model number and a code in the UNLOCKED position (on models letter to ensure proper replacement parts.
  • Page 13: Making The Lp Conversion

    Pliers ZGU36 WB28T10229 JGP975 WB28T10231 JGP963 WB28T10233 Small Flat-Head JGP630 WB28T10235 Screwd river (4m m or 5/32" tip size, JGP628 WB28T10236 Safety Glasses 60mm long) SAFETY INFORMATION _-I ADJUST YOUR COOKTOP FOR SHOULD KNOW USE WITH LP GAS The pressure...
  • Page 14 Installation Instructions MAKING THE LP CONVERSION (CONT.) I-_ CHANGE COOKTOP BURNER I-_ CHANGE COOKTOP BURNER ORIFICES ORIFICES (CONT.) NOTE: On most burners, Remove the top grates, burner caps, the orifices have a spring- Retainer and burner heads. loaded retaining ring Ring Remove This...
  • Page 15 Installation Instructions Units with 4 burners CHANGE COOKTOP BURNER ORIFICES (CONT.) Locate the LP/Propane orifices shipped inside the literature package. They will have a digit number and the letter "L" on the side. (Important: Save the orifices removed from the appliance for future use.) Each orifice...
  • Page 16: Burner Flames

    Installation Instructions MAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLAMES Make the adjustment by slowly turning the screw until flame appearance Turn all burners full on and check the correct. flames. They should be blue in color with Testing Flame Stability: some yellow tipping...
  • Page 17 Instructions Table de cuisson scellee d'installation au gaz de 91 cm (36") JGP628, JGP630, JGP963, JGP970, JGP975, ZGU36 Web a I'adresse • www, electromenagersge,ca Questions? Appelez le Centre de reponse 1.800.561.3344 ou visitez notre site POUR VOTRE SI_CURITI_ AVANT DE COMMENCER -&AVERTISSEMENT...
  • Page 18 Instructions d'installation INSTRUCTIONS IMPORTANTES DE SI CURITI PII_CES COMPRISES La conception de votre table de cuisson a et6 approuve par I'ACNOR International. Vous trouverez des precautions a prendre matiere de securit6 dans votre Guide d'utilisation et de soins. Lisez-les attentivement. 2 vis Bandes de mousse 2 Supports...
  • Page 19 Instructions d'lnstallation LISTE DE VITRIFICATION AVANT INSTALLATION r-cq Enlevez les instructions d'installation Pour preparer I'ouverture de la surface de la trousse de documentation de cuisson, vous devez vous assurer que I'interieur de I'armoire ne touche lisez-les soigneusement avant commencer. pas la table de cuisson (consultez section...
  • Page 20 Instructions d'lnstallation PRI:!:PARATION DE UOUVERTURE 17-1VOUS DEVEZ RESPECTER LES EMPLACEMENT DEGAGEMENTS MINIMAUX RECOMMANDE SUIVANT L'ALIMENTATION DE G.AZ .A PARTIR DU MUR ARRIERE Profondeur max de 33 cm (13") des armoires en surplomb non proteg6es Degagement min. de 2,5 cm (1") min. du mur arriere 15 cm (6") decoupage au mur de c6t6 droite...
  • Page 21: Installation De La Table De Cuisson

    Instructions d'lnstallation INSTALLATION DE LA TABLE DE CUISSON PLACEZ LA PRISE TROUVEZ LES PII_CES DE D'ALIMENTATION MONTAGE ELECTRIQUE ET LE ROBINET Retirez les supports de fixation de la trousse D'ALIMENTATION DE GAZ de documentation. AU-DESSOUS DE L'ARMOIRE N'UTILISEZ JAIVIAIS DES RACCORDS Rodinet d'arr6t i1-_\ I Prise electrique...
  • Page 22 Instructions d'installation INSTALLATIONmBRANCHEMENT DU GAZ 17-1FOURNISSEZ UN BON E_ INSTALLEZ LE RI_GULATEUR EN BAS DE LA BOiTE DE APPROVISIONNEMENT BRULEURS EN GAZ Cette table de cuisson est con_ue pour Vissez fonctionner au gaz naturel a une pression regulateur dans tubulure d'admission de 4 po.
  • Page 23 Instructions d'installation VI_RIFIEZ QU'IL N'Y A PAS INSTALLATION SUR UN FOUR ENCASTRE DE FUITE Avant de verifier qu'il n'y a pas de fuite, Consultez I'installation du four encastre pour assurez-vous que tous les boutons y trouver les instructions d'installation. brQleurs soient en position OFF (arr_t).
  • Page 24 Instructions d'installation INSTALLATION--RACCORDS I LECTRIQUES -'IAVERTISSEMENT _-I ALIMENTATION I_LECTRIQUE ET PRISE Debranchez tout courant electrique au niveau du disjoncteur de la maison ou de la bofte Vous devez utiliser une bonne alimentation fusibles avant d'installer. electrique et une bonne prise pour faire fonctionner les el6ments...
  • Page 25 Instructions d'installation INSTALLATIONmRACCORDS I LECTRIQUES (SUITE) -&MISE EN GARDE : si fixez SITUATION D'UTILISATION OU LE vous CORDON D'ALIIVIENTATION D'UN la broche de raise a la terre de I'adaptateur APPAREIL ELECTROIVIENAGER une vis du couvercle de la prise murale, cela ne met pas a la terre I'appareil, a moins EST INFREQUEMMENT que la vis soit en metal...
  • Page 26 Instructions d'installation BRULEURS DE LA TABLE DE CUISSON r-cq Capuchon de brQleur ASSEMBLEZ LES BRULEURS Assurez-vous les broches DE LA TABLE DE CUlSSON t_tes de brQleur L'electrode de I'allumeur est exposee. Faites correspondent attention de ne pas pousser un contr61e de la T6te de br01eur aux creux de la...
  • Page 27 Instructions d'installation VI RIFIEZ LES ALLUMEURS ALLUMAGE DES BRULEURS Vous devez verifier le fonctionnement Allumage de la table de cuisson - Quand allumeurs electriques apres vous _tre vous mettez le bouton de la table de cuisson soigneusement assure que la table de cuisson en position LITE (allumage), I'allumeur...
  • Page 28 Instructions d'installation BRULEURS DE LA TABLE DE CUISSON (SUITE) _-I LES FLAMMES DU BRULEUR E_ GRILLES DE BRULEUR Les trois grilles de brQleur sont con£ues pour Allumez chaque brQleur. Les flammes doivent leur emplacement particulier. Pour obtenir 6tre bleu sans trace de jaune.
  • Page 29 Instructions d'installation CONVERSION AU GAZ PROPANE (LP) I-_ AJUSTEZ VOTRE PLAQUE RENSEIGNEMENTS RELATIFS A LA SECURITE QUE VOUS DE CUlSSON A UN USAGE DEVEZ CONNA|TRE AU GAZ LP Les diaphragmes du regulateur de pression et Debranchez tout le courant electrique, du br_leur sont regles pour le gaz naturel.
  • Page 30 Instructions d'installation CONVERSION AU GAZ PROPANE (LP) (SUITE) CHANGEZ LES DIAPHRAGMES CHANGEZ LES DIAPHRAGMES DES BRULEURS DE LA TABLE DES BRULEURS DE LA TABLE DE CUISSON DE CUISSON (SUITE) Enlevez les grilles NOTE : Sur la plupart haut, les capuchons breleurs, les diaphragmes Bague de...
  • Page 31 Instructions d'installation Appareil avec 4 br_leurs CHANGEZ LES DIAPHRAGMES DES BRULEURS DE LA TABLE DE CUlSSON (SUITE) Trouvez les diaphragmes de gaz LP/propane joints a la documentation. IIs ont un numero et la lettre {{ L >> inscrite sur un cSte. (Important Conservez les diaphragmes que vous...
  • Page 32 Instructions d'installation CONVERSION AU GAZ PROPANE (LP) (SUITE) Continuez a ajuster en tournant AJUSTEZ LES FLAMMES lentement la vis jusqu'a ce que les DES BRULEURS flammes soient normales. Allumez tousles brQleurs au maximum Essai de stabilite de la flamme • et verifiez les flammes.

This manual is also suitable for:

Jgp630Jgp975Jgp963Zgu36Jgp970

Table of Contents