Agri-Fab 45-0418 Owner's Manual
Agri-Fab 45-0418 Owner's Manual

Agri-Fab 45-0418 Owner's Manual

Atv snow thrower
Hide thumbs Also See for 45-0418:

Advertisement

Quick Links

OWNERS MANUAL
IVlodel No.
45-0418
CAUTION:
Read Rules for
Safe Operation and
Instructions
Carefully
AVERTISSEMENT
Lire et suivre attentivement
les instructions
et
consignes
de securit6
ATV SNOW THROWER
o
Safety
Assembly
Operation
Maintenance
Parts
Securite
Assemblage
Utilisation
Entretien
Pieces
PRINTED IN U.S.A.
FORM NO. 40367 (REV. 2/12/08)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 45-0418 and is the answer not in the manual?

Questions and answers

Summary of Contents for Agri-Fab 45-0418

  • Page 1 OWNERS MANUAL IVlodel No. 45-0418 ATV SNOW THROWER CAUTION: Safety Assembly Read Rules for Operation Safe Operation and Maintenance Instructions Carefully Parts AVERTISSEMENT • Securite Lire et suivre attentivement Assemblage Utilisation les instructions Entretien consignes de securit6 Pieces PRINTED IN U.S.A. FORM NO.
  • Page 2 No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying or recording, or by any information storage or retrieval system, without the express written permission of Agri-Fab, Inc. Unauthorized uses and/or reproductions...
  • Page 3 27 / DESCRiPTiON DESCRiPTiON Snow thrower Housing 6-5/8" Clamp Bracket 6-5/8" Strut Mount Housing Anchor Strap Handlebar Switch 6-5/8" Strut Mount Stabilizer Bracket 5-1/2" Clamp Bracket Actuator 5-1/2" Strut Mount Outer Mount Strut 4" Clamp Bracket Inner Mount Strut 4" Strut Mount Guide Bracket Rear Frame Tube (Bent) Support Bracket...
  • Page 4 ____--1/ ,-------'-3 -------1 ----------1 -------1 -------1 PARTS NOT SHOWN FULL SiZE...
  • Page 5: Tools Needed

    DESCRiPTiON = REF DESCRiPTiON Clevis Pin, 1/2" x 3-1/2" Nylock Nut, 1/2-13 Clevis Pin, 1/2" x 2" Lock Nut, 1/2-13 Hex Bolt, 5/16-18 x 1" Carriage Bolt, 5/16-18 x 1-3/4" Hex Bolt, 1/2-13 x 3-1/2" Carriage Bolt, 5/16-18 x 1" Washer, 1/2"...
  • Page 6 Secure the relay pack near the battery of the ATV or 12. Attach the tethered safety switch to the handlebar using other location on the ATV out of harms way. (4) pre-assembled screws and (4) pre-assembled nuts. Thread the 3 wire lead from the relay pack forward See figure 5.
  • Page 7: Snow Thrower Assembly

    Slide a collar over the end of the outer mount strut. SNOW THROWER ASSEMBLY Slide the outer mount strut through the brackets assembled in step 2. Remove any CV boot guard or stick guard from the Slide a second collar over the end of the outer mount front lower A arms of the ATV.
  • Page 8 11. Placea 15" concreteblock underneath the snow 13.Attachthefrontholesofthe housing anchor s traps to thrower, beneath theengine. S eefigure10. theweldboltsonthehousing using(2) 1/2"locknuts. Do not tighten yet. CAUTION: Use caution while working on snow thrower when it is propped up on concrete block. 112"...
  • Page 9 16. Attachthe bentrearframetubeto the pushchannel 19. Place the wheel assembly behind the engine mounting using(2)1/2"x 3-1/2" hexbolts, ( 4) 1/2"washers and base. (2)1/2"nylock nuts.Donot tighten yet. 20. Fasten the bottom of the anchor brackets (part of 17. Remove the concrete block from under the engine wheel assembly) to the outside of the mounting tubes and place it underneath the the end of the rear frame...
  • Page 10 25. Assemble the guidebracket a nd guideplateto the 28. Place the discharge chute (facing forward) onto the mounting t ubesusing (2)5/16" x3"hexboltsand5/16" ring. Attach (3) chute keepers (right side up as shown) nylock nuts.Donottightenyet. to the bottom of the flange using (6) 1/4" x 1" hex flange 26.
  • Page 11 30. Attachthe controlassembly's s upporttube to the SECURE CABLES HERE weldedbracket b elowthe discharge chuteusing(2) 5/16"x 1-1/4" c arriage boltsand(2)5/16"nylock nuts. Do not tighten yet. 31. Tighten bolts assembled in steps 29 and 30. CHUTETILT/< CONTROL BOWED_t _5/16"NYLOCN WASHER FIGURE 25 38.
  • Page 12 42. Slidetherearframe tubein oroutofthepushchannel 45. Tightenthenutsandboltsthatfasten thepushchannel to alignit withtheATVhitch. M akesurethe minimum to themounting tubes, a ndtherearframetube.Refer 3"-4" clearance b etween t heATVandthesnow thrower to figures14 and15. Makesurethe mounting tubes is maintained. staycentered withtheATVwhiletightening. 43. If therearframe tubedoesnotslidein or outenough 46.
  • Page 13 KNOWYOUR S NOWTHROWER Read this owner's manual and safety rules before operating your snow thrower. Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations. CHUTE TiLT LEVER HANDLE CRANK ON/OFF SWITCH UPPER CHUTE LOWER CHUT_'_ SWITCH...
  • Page 14: Raising Andlowering

    CONTROLLING SNOW DISCHARGE It is advisable to operate the ATV at a slow ground • Tocontrol t hedirection snowis thrown, t hedischarge speed for safe and efficient snow removal. chutehas180degrees of rotation. Turn thecrankrod In deep, drifted or banked snow it will be necessary to clockwise t orotate thechute totheright.
  • Page 15 CUSTOMER RESPONSIBiLITiES • Read and follow the maintenance schedule and the maintenance procedures listed in this section. MAINTENANCE SCHEDULE Fill in dates as you Service Dates complete regular service. Check for loose fasteners Check scraper and shoes for wear Cleaning Lubrication Section Check engine oil level Maintain engine per instructions below and in engine manual.
  • Page 16: Removing T Hebelt

    REMOVING T HEBELT (Figures 32-35) • Remove the key and disconnect the spark plug wire DRIVE COVER from the snow thrower. • Remove the engine pulley cover, the drive cover and the skid plate from the snow thrower. Disengage the snow thrower clutch. Remove the belt from the top pulley.
  • Page 17 STORAGE RECOMMENDATIONS PARTS TO REMOVE AT END OF SEASON • Clean the snow thrower thoroughly. Wash off any salt Remove the A-arm brackets from the suspension deposit which may have dried on the thrower and of the ATV, especially before using your ATV for off- housing.
  • Page 18 .,90 SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE N,,= £ _> ,,,,J > CAUTION: DO NOT OPERATE YOUR ATV AND SNOW THROWER ON A SLOPE iN EXCESS OF 10 DEGREES. BE SURE OF YOUR ATV'S TOWING AND BRAKING CAPABiLiTiES BEFORE OPERATING ON A SLOPE.
  • Page 19 REPAIR PARTS FOR MODEL 45-0418 ATV SNOW THROWER /®...
  • Page 20 REPAIR PARTS FOR MODEL 45-0418 ATV SNOW THROWER PART NO. DESCRIPTION PART NO. DESCRIPTION 65683 47189 50" Snow thrower Housing Nylock Nut, 1/4-20 71464 731-1300C Lower Chute Drive Assembly 63768 731-0921 Impeller Upper Chute 65685 750-0437 Spiral Blades (LH) Pivot Bushing 65684 731-0851A Spiral Blades (RH)
  • Page 21 REPAIR PARTS FOR MODEL 45-0418 ATV SNOW THROWER 42 52\ •...
  • Page 22 REPAIR PARTS FOR MODEL 45-0418 ATV SNOW THROWER PART NO. DESCRIPTION PART NO. DESCRIPTION 65699 Crank Rod Support 736-0247 Washer, .41 x 1.25 x .156 603-0302 Chute Tilt Bracket 43001 Hex Bolt, 3/8-16 x 1" 684-0061 Crank Chute Assembly 43003 Lock Washer, 3/8"...
  • Page 23: Repair Parts

    Brake Release Strap 43062 Hex Bolt, 3/8-16 x 1-1/2" 712-3008 Hex Jam Nut, 3/8-16 43001 Hex Bolt, 3/8-16 x 1" 43082 Hex Lock Nut, 3/8-16 40741 Harness 25944 Cable Strap REPAIR PARTS Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 www.agri-fab.com...

Table of Contents