Recalling The Stored Equalizer Curve; About The Crossover - Alpine CDA-9887R Owner's Manual

7
Turn the Rotary encoder to select PROTECT
YES/NO, and then press
adjusted contents.
PROTECT YES
(Initial setting)
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, "REPLACE NO/YES" can be selected.
• If NO is selected, the preset is stored.
8
After setting, press and hold
seconds to return to normal mode.
• This function is inoperable when DEFEAT is set to ON (page 16).
• The stored contents can be recalled by performing operation in
"Recalling the Stored Equalizer Curve" (page 18).
• Pressing AUDIO/RTN when Graphic EQ is adjusted will return to
the previous item.
• If MultEQ is turned on, the A.SEL button is ineffective. For details,
refer to "Turning MultEQ on/off" (page 16).
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.

Recalling the Stored Equalizer Curve

1
Press A.SEL to recall the DSP adjust mode.
Media Xpander Crossover
Parametric EQ / Graphic EQ
2
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press
3
Press any one of the preset buttons (1 through
6) that has your desired equalizer characteristic in
memory.
4
Press the preset buttons again to return to the DSP
adjust mode.
5
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• This function is inoperable when DEFEAT is set to ON (page 16).
• You can recall the adjusted equalizer curve from "Equalizer Presets"
(page 16).
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.

About the Crossover

Crossover (X-OVER):
This unit is equipped with an active crossover. The crossover limits the
frequencies delivered to the outputs. Each channel is controlled
independently. Thus, each speaker pair can be driven by the frequencies
for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass filter) of
each band, and also the slope (how fast the filter rolls off the highs or lows).
Adjustments should be made according to the reproduction
characteristics of the speakers. Depending on the speakers, a passive
network may not be necessary. If you are unsure about this point, please
consult your authorized Alpine dealer.
18
-EN
/ /ENT to store the
PROTECT NO
/ESC for at least 2
T.Correction
Media Xpander
/ /ENT.
4.2ch (F/R/Sub-W) mode
Cut-off frequency
(1/3 octave steps)
HPF LPF
Low range 20 Hz -
----
speaker 200 Hz
Rear high
20 Hz -
range ----
200 Hz
speaker
Front high
20 Hz -
range ----
200 Hz
speaker
Low range
(Different from actual display)
2.2ch (3WAY) mode
Cut-off frequency
(1/3 octave steps)
HPF LPF
Low range 20 Hz -
----
speaker 200 Hz
Mid range 20 Hz - 20 Hz -
speaker 200 Hz 20 kHz
1 kHz -
High
20 kHz,
range ----
(20 Hz -
speaker
20 kHz)
*
* Only when selecting User's in "Setting the Response Slope for the
High Range Speaker (TW Setup)" (page 27).
Low range
(Different from actual display)
Slope
HPF LPF
FLAT, 6,
---- 12, 18,
-12 dB
24 dB/oct.
FLAT, 6,
12, 18, ----
-12 dB
24 dB/oct.
FLAT, 6,
12, 18, ----
-12 dB
24 dB/oct.
High range
Slope
HPF LPF
FLAT, 6,
---- 12, 18,
-12 dB
24 dB/oct.
FLAT, 6, FLAT, 6,
12, 18, 12, 18,
-12 dB
24 dB/oct. 24 dB/oct.
FLAT
*
6, 12, 18, ----
-12 dB
24 dB/oct.
Mid range High range
Level
0 to
0 to
0 to
Level
0 to
0 to
0 to