Sound Setting; Adjusting Bass/Treble/Balance (Between Left And Right)/Auto Volume/Fader (Between Front And Rear)/Defeat; Turning Multeq On/Off; Equalizer Presets - Alpine CDA-9887R Owner's Manual

Sound Setting

Rotary encoder
/ /
/
ENT SOURCE
AUDIO/RTN MultEQ
/
ESC
A.SEL FUNC./SETUP
Adjusting Bass/Treble/Balance (Between
Left and Right)/Auto Volume/Fader
(Between Front and Rear)/Defeat
1
Press AUDIO/RTN repeatedly to choose the desired
mode.
Each press changes the mode as follows:
1
*
SUBWOOFER BASS
3
FADER * AUTO VOLUME
1
SUBWOOFER *
Subwoofer: 0 ~ +15
Bass level: – 7 ~ +7
Treble level: – 7 ~ +7
Balance: L15 ~ R15
Fader: R15 ~ F15
Auto Volume: OFF/LOW/MIDDLE/HIGH
Defeat: ON/OFF
Volume: 0 ~ 35
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, BALANCE, FADER, AUTO
VOLUME or DEFEAT mode, the unit automatically returns to
normal mode.
1
* When the subwoofer mode is set to OFF, its level cannot be adjusted.
2
* When the MultEQ (page 16) is set to OFF, its level cannot be
adjusted.
3
* If you set the 4.2ch/2.2ch switch (pages 40 to 42) to 2.2ch, you
cannot adjust this mode.
4
* By setting AUTO VOLUME, the unit can automatically adjust
volume to a proper level according to engine/road noise, etc. There
are three volume correction degrees: LOW, MIDDLE and HIGH.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS,
TREBLE and EQ will return to the factory defaults, and MX
(page 22) is turned off.
• Depending on the connected devices, some functions and display
indications do not work.

Turning MultEQ on/off

MultEQ, developed by Audyssey Labs, automatically corrects the audio
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this, MultEQ must take
measurements of the vehicles response characteristics. For details on the
set up procedure, consult your authorized Alpine dealer.
16
-EN
BAND/TA
Preset buttons
(1 through 6)
2 2
* *
TREBLE BALANCE
4
* DEFEAT VOLUME
Press MultEQ to select ON/OFF mode.
• If MultEQ is turned on and its button pressed and held for at least 2
seconds, the Curve mode is switched (only when curve1 and curve2 are
stored).
• When using MultEQ, MX, X-OVER, T.Correction, User's EQ,
Parametric EQ and Graphic EQ are set automatically. They are no
longer user adjustable.
• When an external audio processor is connected, the MultEQ function
cannot be used.

Equalizer Presets

10 typical equalizer settings are preset at the factory for a variety of
musical source material.
1
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
2
Turn the Rotary encoder to select AUDIO mode,
and then press /
Bluetooth GENERAL
TUNER Bluetooth
3
Turn the Rotary encoder to select Factory's EQ
mode, and then press
4
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press
Flat Pops Rock
Electrical Dance Hip Hop&Rap
Country Classical
User4 User5 User6
• By selecting User's 1 to 6, you can recall the stored preset number in
"Adjusting and Storing the Graphic Equalizer Curve" (page 17) or
"Adjusting and Storing the Parametric Equalizer Curve" (page 17) .
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
• This function is inoperable when DEFEAT is set to ON (page 16).
• Press and hold /ESC for at least 2 seconds, the setting mode is
cancelled.

Setting EQ mode

This setting gives you a choice of 5-band parametric, or 7-band
graphic equalizer.
1
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
2
Turn the Rotary encoder to select AUDIO mode,
and then press /
Bluetooth GENERAL
Bluetooth
3
Turn the Rotary encoder to select EQ Mode, and
then press / /ENT.
/ENT.
AUDIO DISPLAY
/ /ENT.
/ /ENT.
News Jazz&Blues
Easy Listening
User1 User2 User3
/ENT.
AUDIO DISPLAY TUNER