Table of Contents
Related Manuals for Craftsman 351.215131
Summary of Contents for Craftsman 351.215131
- Page 1 Operator's Manual I CRAFTSMAN°I 2 x 42" Belt 6" Disc SANDER Model No. 351.215131 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sea rs.com/craftsma 24686.00 Draft (06/20/06)
- Page 2 CRAFTSMAN TOOL TOOL SHOULD BE MAINTAINED If this Craftsman tool fails due to a defect in material or • Always unplug tool prior to inspection. workmanship within one year from the date of purchase CALL 1-800-4-MY-HOME® TO ARRANGE FOR FREE •...
- Page 3 • Use recommended accessories (refer to page 13). • Center abrasive on aluminum disc and press to paste. Use of improper accessories may cause risk of • Make sure abrasive is pasted evenly on the aluminum injury to persons. disc. •...
-
Page 4: Power Source
• Thread the horizontal stop bar into the threaded hole • Inspect tool cords periodically, and if damaged, have repaired by an authorized service facility. on the rear side of belt housing. • Green (or green and yellow) conductor in cord is the •... -
Page 5: Electrical Connections
DESCRIPTION • Be sure motor runs clockwise on disc side. Abrasive Craftsman 2 x 6" Belt and Disc Sander has a 2" x 42" belt must travel down. belt and 6" disc for deburring, beveling and sanding •... -
Page 6: Mount Sander
• Replace abrasives w hentheybecome loaded REPLACING ABRASIVE BELT (glazed) o r frayed. Refer to Figures 7 and 8. • Whengrinding metal, m oveworkpiece a crossabra- WARNING: Disconnect sander from power source siveto prevent h eatbuiltup. before making any adjustments. •... -
Page 7: Contour Sanding
_sting Bolt Move the workpiece against belt. Belt will follow contour. Locking Figure 10 - Contour Sanding SHARPENING Refer to Figure 11. • Adjust belt table to desired sharpening angle and tighten securely. Use belt sander to notch the back Figure 9 -Tracking Belt of an auxiliary piece of wood. - Page 8 • A work stop with nut is provided to be used when • Move the workpiece across the down side (right) of the abrasive disc. The abrasive disc moves fastest straight sanding in the horizontal position. and removes more material at the outer edge. •...
-
Page 9: Keep Tool In Repair
KEEP TOOL IN REPAIR Any attempt to repair motor may create a hazard unless repair is done by a qualified service technician. Repair • If power cord is worn, cut, or damaged in any way, service is available at your nearest Sears store. have it replaced immediately. - Page 10 Model 351.2151 30 Figure 15 - Replacement Parts Illustration for Sander...
- Page 11 PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. 08425.00 Thru Bolt 24708.00 Lower Belt Guard STD315225 01002.00 10-1.5 x 25mm Socket Head Bolt Bearing 6202ZZ* Motor Fan STD852010 10mm Lock Washer* 24677.00 Armature STD851010 10mm Fiat Washer* 24678.00 04662.00 Belt Table 24679.00 Stator with Housing Endshield...
- Page 12 AI_IO GARANTIA COMPLETA DE UN PARA uso no intencional de las herramientas mecanicas. HERRAMIENTA CRAFTSMAN ES IMPORTANTE MANTENER HERRAMIENTAS Siesta herramienta Craftsman fallara por causa de defectos en el material o en la mano de obra en un lapso de un aho a partir de •...
- Page 13 • Evite el arranque por accidente. AsegOrese que el interruptor de la herramienta esta en la posici6n "apagado" (off) antes de enchufarla Refierase alas Figuras 2 y 3. • No fuerce la herramienta. Trabajar,_ en la forma m,_s eficiente a la velocidad para la cual fue dise_ada.
- Page 14 Tomacorriente conectado a tierra correctamente Punta de conexi6n a tierra Barra de retenci6n Enchufe horizontal Mesa de la correa 3 puntas Figura 4 - Receptaculo de 3 puntas • No remueva ni altere la punta de conexi6n a tierra de ninguna manera.
-
Page 15: Cordones De Extension
Muchos de los tornillos de la plancha de cubierta, las tube- Las Ifneas de energfa electrica se insertan directamente en el rias de agua y las cajas de tomacorriente no estan conecta- interruptor. La Ifnea de conexi6n a tierra verde debe permanecer dos a tierra correctamente. - Page 16 • AsegOrese que todos los sujetadores esten apretados y que Use una escuadra de combinaci6n para ajustar la mesa de la no se hayan soltado con la vibraci6n. correa a 45 ° o 90 ° con respecto a la platina de la correa.
- Page 17 • Apriete los pernos para fijar la platina. • Si la correa no estA centrada sobre las ruedas, ajuste el alinea- miento de la correa segLin se explica en la siguiente secci6n. • Monte la cubierta de la correa y apriete las manillas. •...
- Page 18 • Afloje el perno de fijaci6n de la caja; incline la caja de la CAMBIO DISCO ABRASIVO correa a la posici6n horizontal y apriete el perno para fijar Refierase a la Figura 2, pb.gina 15. la posici6n de la caja. ADVERTENClA: Desconecte la lijadora...
- Page 19 • No aplique la cera a la platina de la correa. La correa puede ADVERTENClA: Despues de lijar madera o material no met&li- co, siempre limpie el aserffn del colector y de las protecciones recoger la cera y depositarla sobre las ruedas, haciendola que se resbale.
- Page 20 SINTOMA MEDIDA CORRECTIVA CAUSA(S) POSIBLE(S) El motor no arranca 1. Voltaje bajo 1. Revise la energfa para ver si tiene el voltaje apropiado 2. Hay un circuito abierto en el motor 2. Inspeccione todas las conexiones de entrada en el o hay conexiones sueltas motor para verificar si hay alguna suelta o abierta 3.
- Page 21 NOTAS...
- Page 22 NOTAS...
- Page 23 NOTAS...
- Page 24 Your Home For repair v in your home v of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-youre For Sears professional installation of home appliances and items like garage door openers and water heaters.