14 in. bar 2.5 peak hp motor electric chain saw (32 pages)
Summary of Contents for Craftsman 358.348211
Page 1
Instruction Manual Manuel d'instructions Betriebsanweisung Manual de instrucciones 358.348211 CRAFTSMAN" English Please read these instructions carefully and make sure you understand them before using this unit. Fran£ais Avant d'utiliser cet appareil, veuillez lire attentivement les instructions assurez-vous de les avoir comprises.
Page 2
Chain Front Hand Guard Front Handle Adjustment Tool ('_.w / (Bar Tool) Starter Rope _#_ I Idle Speed Screw _'_'_//%*/ ON/STOP Chain Muffler _ _4_,_,._,,Switch _\J-_Primer r/lUll Bulb 7,OJ-_.Z Throttle Chain Cylinder Cover Rear Lockout Adjustin Direction Screw of Travel Handle Thro_le Choke/...
• Keep children, bystanders, and animals a teners securely tightened. minimum of 10 Meters away from the work • Use only Craftsman ® accessories and re- area. Do not allow other people or animals placement parts as recommended. to be near the chain saw when starting or...
lated p lace; and use anapproved, marked centainer forall f uel purposes. Wipe u pall Kickback Path fuel spills b efore starting saw. • Move atleast 10 feet ( 3meters) from fuel- ing site before starting engine. • Turn the engine offand letsaw cool i na non-combustible area, not o ndry leaves, straw, paper, etc.Slowly remove fuel c ap...
Symm_ Large Radius Tip Elbow locked • Low-Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter. Thumb on underside of Low-Kickback Chain handlebar Contoured Depth Gauge Deflects Kickback •...
Page 6
skin color or texture, or loss of feeling in the SAFETY NOTICE: Exposure fingers, hands, or joints, discontinue the use vibrations through prolonged use of gasoline of this tool and seek medical attention. An powered hand tools could cause blood anti-vibration system does not guarantee the vessel...
Page 7
Pull the choke/fast idle lever out to the full Use only 15"-18" ofrope per p ull. extent to set the throttle, then return the Hold s aw firmly w hile p ulling s tarter rope choke/fast idle lever to the OFF CHOKE position.
Page 8
your grip around the front handle. The chain the front handle with your left hand. Hold the should stop immediately. chain saw approximately 14" (35 cm) above Inertia a stump or other wooden surface. Release activating function control your grip on the front handle and use the weight of the saw to let the top of the guide _kWARNING: When performing the...
Page 9
Hinge holds tree on stump and helps control fall _,_'_ Opening _,\\'_,'\_ of felling /cut Turn saw OFF and use a plastic or wooden wedge to force cut open. Overcutting begins on the top side of the log with the saw against the log. When overcut- c'os_ngof._,l'('f¢\ fing use light downward pressure.
Page 10
• Start at base of the felled tree and workto- ward the top, cutting branches and limbs. Remove small limbs with one cut. • Keep the tree between you and the chain as much as possible. • Remove larger, supporting branches with the I/3, 2/3 cutting techniques described in the bucking section.
3. Turn adjusting screw clockwise untl • When rail top is uneven, use a fiat file to re- chain solidly contacts bottom of guide store square edges and sides. bar rail. '_-q-- Fte Rail Edges_r] and Sides I U I Square Worn Groove Correct Groove...
Page 12
7. Carefully remove the new chain from the £J, aWARNING: Disconnect the spark package. Hold chain with the drive links as shown. plug before performing maintenance, ser- vice or adjustments, except for carburetor Cutters Depth Gauge adjustments. CHAIN SHARPENING Chain sharpening is a complicated task that requires special tools.
• Do not store the unit or fuel in a closed area STORAGE where fuel vapors can reach sparks or an WARNING: Stop engine and allow to open flame from hot water heaters, electric motors or switches, furnaces, etc. cool, and secure the unit before storing or •...
Page 14
2000/14/EC Poulan/Weed Eater, Division Electrolux North America, Inc., Texarkana, TX, 75501, USA, T_L : +1 903 223 4100, declare under sole responsibility that the Craftsman model 358.348211 chain saw was assessed in accordance with Annex V of the...
Page 15
MODEL: Craftsman 358.348211 ENGINE Cylinder volume, cm 3 Stroke, mm Idle speed, rpm 3,000 Recommended max speed, unloaded, 13,000 Power kW IGNITION SYSTEM Manufacturer Walbro Type of ignition system Spark plug Champion Electrode gap, mm FUEL AND LUBRICATION SYSTEM Manufacturer...
Need help?
Do you have a question about the 358.348211 and is the answer not in the manual?
Questions and answers