Craftsman 137.214130 Operator's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Saw
  5. 137.214130
  6. Operator's manual

Craftsman 137.214130 Operator's Manual

1/2 hp (max. developed) 2480 f.p.m. (no load) 9" band saw
Hide thumbs

Advertisement

Table of Contents

CAUTION:
Before
using this Band Saw,
read this manual
and folJow
all its Safety
RuIes and
Operating
instructions
÷
Safety Instructions
÷
installation
÷
Operation
® Maintenance
® Parts List
Sears,
Roebuck
and Coo, Hoffman
Estates,
_L 60119 U.SoAo
Visit
our Cra_sman
website:
w'_Lsears.cornJcraflsman
Part
Noot37o2141300t

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 137.214130

Summary of Contents for Craftsman 137.214130

  • Page 1 CAUTION: ÷ Safety Instructions Before using this Band Saw, ÷ installation read this manual and folJow all its Safety RuIes and ÷ Operation Operating instructions ® Maintenance ® Parts List Sears, Roebuck and Coo, Hoffman Estates, _L 60119 U.SoAo Visit our Cra_sman website: w'_Lsears.cornJcraflsman...

  • Page 2: Specifications

    SECTION PAGE 12.ALWAYS WEAR EYE PROTECTION. Any Band Saw GENERAL SAFETY #NSTRUCT1ONS Warranty ............................can [hrow foreign objects into Ihe eyes that could Products Specifications ........................ BEFORE USnNG THE BAND SAW cause permanent eye damage. ALWAYS wear Safety Safety instructions ........................
  • Page 3 24.DO NOT OPERATE the toot if you are under the SMALL PIECES should be secured with jigs or ELECTRICAL REQUIREMENTS as the current stamped on Ihe motor nameplate. influence of any drugs, afcohol or medication that fixtures. Do not hand hold pieces that are so small Running at a lower voltage wilt damage the motor.

  • Page 4: Product View

    RECOMMENDED ACCESSORIES UNPACKING AND CHECKING CONTENTS Carefully unpack [he band saw and all its parts, and To avoid iniury: compare against the illustration following. Place the saw Use only accessories recommended for this band on a secure surface and examine i[ carefully.

  • Page 5: Glossary

    BAND SAW TERMS KERF -- The material removed by the blade in a Ihrough ASSE ]BLY NSTRUCT ONS cut, or the slot produced by the blade in a non-through or SAW[3UST COLLECTION PORT (F_G. C) BLADE GUIDES -- Support the blade and keep it Item TOOLS NEEDED partial cut.

  • Page 6: Adjustment

    INSTALLING ANDREMOVING B LADES (FIG. E ) Fig. E BLADE TENSION (FIG. 1) Toavoid injury from accidental stalling, always t urnthe To avoid injury, turn the switch OFF and disconnect switch OFFandremove p ower c ordplugfrom power saw from the power source before making any soclrce b efore removing orreplacing t heblade.
  • Page 7 BLADE TRACKING {FIG. J) UPPER BLADE GUtDE ASSEMBLY (FIG. K) UPPER BLADE GU!DES AND BLADE SUPPORT Support bearing (Fig. IVl) BEARING (FIG, L, M) Loosen the screw (6). Move the support bearing (8) in or out, until the bearing is 1/64." behind the blade. To avoid injury, turn the switch OFF and disconnect To avoid injury, turn the switch OFF and clisconnect the 16.

  • Page 8: Operation

    Fig, N LOWER BLADE GUIDES AND SUPPORT BEARING (FIG. N, O) GENERAL CUTTING BASIC SAW OPERATIONS To avoid injury, turn the switch OFF and disconnect saw from the power source before making any "ON/OFF" SWITCH (FIG. P) For your safety, read and understand all GENERAL adjustments.
  • Page 9 SELECTION (HG. Curve Cuttirtg- t/8, 1/4 Do not allow filth to build up on the table, the guides, or the support bearings. Clean them with Craftsman CAUTION: Blade teeth are sharp. Use care when Gum and Pitch Remover. handling a saw blade.

  • Page 10: Troubleshooting

    MOTOR Problem [Probable Cause Noisy operation. . Incorrect belt tension. 1. AdjusE tension. See ASSEMBLY ADJUSTMENTS section INSTALL THE BELT. To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source before 2.

  • Page 11: Parts List/Exploded View

    NO. 137.2t4130 SCHEMATIC When servicing use only CRAFTSMAN repiacement parts. Use of any ether parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Band Saw may create a HAZARD Lmless repair is done by a qualified service technician.
  • Page 12 MODEL NO. !37.2!4!30 9 '_ BAND When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. SCHEMATIC Any attempt to repair or replace electrical parts on this Band Saw may create a HAZARD unless repair is done by a qualified service technician.

Table of Contents