Craftsman 315.275062 Owner's Manual page 3

RULES FOR SAFE OPERATION (Continued)
15. SECURE WORK. Use ctampsor a vise tohold work Bolh hands are needed to operate the tool
16_ DON'T OVERREACH, Keep properfooting and balance at alltimes Do not use on a ladderor unstablesupport
17. MAINTAIN TOOLS WITH CARE Keep tools sharpat afltimes, and cleanfor bestand safestperformance. Follow
instruclions for lubricating and changingaccessodes_
18. DISCONNECT TOOLS, When not in use, before servicing, or whenchangingaltachments, blades, bits, cutters,
etc., all tools should be disconnectedf.rampowersupply.
19.. REMOVE ADJUSTING KEYS AND WRENCHES, Formhabitofchec.kingtoseethatkeysandadjuslingwrenches
are removed from toolbefore turningit on..
20., AVOID ACCIDENTAL STARTING. Don't carry plugged-in tools with finger on switch Be sure switchisoff when
plugging in.,
21. MAKE SURE YOUR EXTENSION CORD IS IN GOOD CONDITION. When using an extension cord,be sureto use
one heavy enoughto carry the currentyour produclwittdraw.An undersized cordwillcause a drop tn linevoltage
resulting in loss of power and ove_eattng. A wlre gauge size (A.W.G) of at least 14 is recommendedfor an
extensioncord 25 feet or less In length., A cord exceeding25 feet is not recommended, i1in doubt, use lh next
heaviergage. The smallerthe gage number, the heavierthe cord
22. OUTDOOR USE EXTENSION CORDS, When tootis used outdoors,use only extensioncords suitable for use
outdoors, Outdoor approvedcordsare marked withthe suilixW,.A,for example - SJTW-A or SJOW_A.
23. KEEP CUTTERS CLEAN AND SHARP. Shaq_ cuttersminimizeslallingandkickback.
24. KEEP HANDS AWAY PROM CUTTING AREA. Keep handsaway from cutlers. Do not reach underneathwork
while cutteris rotating. Do not attempt toremovematerialwhilecutteris rotating
25 NEVER USE IN AN EXPLOSWE ATMOSPHERE. Normalsparkingel the motor couldignite fumes.,
26 INSPECT TOOL CORDS PERIOOICALLY and if damaged, have repaired at your nearest Sears Repair Center
Stay constantly aware el cordlocation.
27,. INSPECT EXTENSION CORDS PERIODICALLY andreplacetfdamaged.
28 KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE, Always use a cleanclolhwhencleaning.
Never use brake fluids,gasoline, petroleum.based producls or any strong solventsto cleanyour tool,
29 STAYALERT. Watchwhat you are doing anduse commonsense. Donor operate tool when you are tired, Donot
rush.
30 CHECK DAMAGED PARTS. Before ludheruse of the tool,a guardor otherpart thatis damaged should be carefully
checked todetermine that ttwilloperate properlyand perform itsintendedfunction,.Check for alignment of moving
parts, blndtng of moving parts, breakage of parts, mounting, and any otherconditions thai may affeclits operation., A
guard or other part that ts damaged should be propedy repaired or replaced by an authorized service center unless
Indicated elsewherein thtsinstruction manual
31. DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an
authorizedservicecenter
32 Inspectfor and removeall nailsfrom tumber before muting..
33 DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence oFdrugs, alcohol, or any
medication
34. WHEN SERVICING USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS.
35 POLARIZED PLUGS, To reduce the rfskofelectricshock,thistoolhasa polarizedplug(one blade iswiderthan the
other), This plugwtl!fit in a polarized outlet only one way. If the plugdoes not fit fully in the outlet, reverse theplug.
if it stltldoes notfit,contacta qualifiedelectricianto install the proper outteL Do not change lhe plugin any way.
36. DO NOT USE TOOL UNDER "BROWN-OUT" OR OTHER LOW VOLTAGE CONDITIONS, Also. do notuse with
any devicethat could cause lhe power supply voltageto change,,
37. WHEN USING THIS ROUTER WITH A ROUTER TABLE, HELP PREVENT POSSIBLE SERIOUS INJURY BY
KEEPING THE Cbq'TER GUARDED AT ALL TIMES. Useonlyrouter tables,wlih guards,thathave beendesigned
for use on reuters thai are of thistype, size, and weigh!
38 SAVE THESE INSTRUCTIONS. Review them frequently and use them to Instructotherswho may use Ibis tool If
youloan someone thistool, loan them theseinstructions also.
Page 3