Subscribe to Our Youtube Channel
Related Manuals for Altinex MX2214RM
Summary of Contents for Altinex MX2214RM
- Page 1 SWITCHERS MANUAL PART NUMBER: 400-0009-003 PRODUCT REVISION: 0 MX2214RM 4 - IN, 1 - OUT RGBS SWITCHER USER’S GUIDE...
-
Page 2: Table Of Contents
We appreciate your selection of our products and are confident that you will join the ranks of our many satisfied customers throughout the world. This manual covers: MX2214RM – 4– in, 1 - out RGBS Switcher SWITCHERS TABLE OF CONTENTS PRECAUTIONS / SAFETY WARNINGS ...2 GENERAL ... -
Page 3: Precautions / Safety Warnings
Do not pull the power cord or any cable that is attached to the MX2214RM Switcher. If the MX2214RM Switcher is not to be used for an extended period of time, disconnect the power cord from the power outlet. -
Page 4: About Your Switcher
Altinex, Inc. could void the user’s authority to operate the equipment. ABOUT YOUR SWITCHER The MX2214RM is a 4-in, 1-out high resolution RGBS relay switcher designed to allow the connection of as many as four computer video or broadcast video sources to a single presentation display. -
Page 5: Description Of Mx2214Rm
Cross-talk Coupling Power External Power Adapter Power Consumption Table 3. MX2214RM Electrical DESCRIPTION OF MX2214RM -48dB @ 10 MHz 90-140V/200-240V 10 watts max. SWITCHERS... -
Page 6: Select Input
LED of the selected channel should light. selected 4.7 ANALOG OUTPUT The analog output of the MX2214RM can be used for controlling several switchers simultaneously. The analog amplifier drives analog output pin 9 on a 9-pin “D” connector. The output can switch from 0 V to approximately 5.0 V. -
Page 7: Application Diagram
In addition to forward connection, the MX2214RM can be hooked up in reverse direction. In this configuration one video source is selectively sent to each of the video monitors. This capability is referred to as bi-directional switching. In this configuration only one display device can be operational at any given time. -
Page 8: Operation
OPERATION 7.1 RS-232 CONTROL The MX2214RM Switcher uses a Female 9-pin HD connector on its rear panel that allows access to a variety of control capabilities. PIN No. No connection RS-232 Transmit RS-232 Receive No connection Ground Multiple Switcher Loop... -
Page 9: Master-Slave Configuration
- Minimum input number mm - Maximum input number This command is designed to allow the MX2214RM to program each of the inputs to respond to a selected range of input commands. For example, if command [SET10104] is issued, then the following commands will select only Input 1: [I01O01], [I02O01], [I03O01], [I04O01]. -
Page 10: Manual Loop Control
MX2214RM are connected together to form a single switcher. When the input channel button is pressed the loop control pin is internally grounded and the MX2214RM Switcher selects INPUT 4 as the default input. In this configuration the loop control pin 6 on the 9 pin D connector is connected to the same pin on all switchers. -
Page 11: Accessories
Figure 5 If you want to make a 7 by 1 switcher using two 4 by 1 switchers, the following commands should be used to control these switchers: Input 1 through Input 4 Input 5 through Input 7 This will setup each switcher as a different output number. -
Page 12: Frequently Asked Questions
LED lights flash. This is does not designed to avoid accidental respond. resetting. Why? Can the The MX2214RM can be rack MX2214RM mounted by itself or with two be rack units side by side. The width mounted? of the unit is 1/2 rack wide. -
Page 13: Altinex Policy
Make sure that the cables are made according to manual, where the RX pin of the MX2214RM is connected to the TX pin of the computer. If you are controlling the unit by RS-232 command, make sure there is a minimum delay of 100 milliseconds before sending the next command.
Need help?
Do you have a question about the MX2214RM and is the answer not in the manual?
Questions and answers