Table of Contents
Advertisement
Available languages
Available languages
• iMPORTANT
SAFETY iNFORMATiON
WARNING:
When using electric gardening
tool, basic safety precautions should always
be followed to reduce the risk of fire, electric
shock, and personal injury. Carefully read and
understand the entire Operator's Manual before
using your trimmer. Pay close attention to the
Operating Instructions and Safety Warnings.
READ ALL iNSTRUCTiONS
ELECTRICAL
SAFETY
WARNINGS
o This tool is double-insulated.
Use only identical
replacement parts when servicing. Repair or replace
damaged cords.
• WARNING: To reduce the risk of electrical shock, use
only extension cords approved for outdoor use, such
as an extension cord of cord type SW-A, SOW-A,
STW-A, STOW-A, SJW-A, SJOW-A, SJTW-W or
SJTOW-A. A 2-wire extension cord (an extension cord
without a ground) may be used because the tool is
double insulated. However, a 3-wire extension cord
(an extension cord with a ground) that uses a NEMA
type connector (parallel blade, U ground) may also be
used. Extension cords are available from your local
retailer. Use only round-jacketed
extension cords
approved for outdoor use.
To reduce the risk of electrical shock, this unit has a
polarized plug (one blade is wider than the other) and
will require the use of a polarized extension cord. This
unit plug will fit into a polarized extension cord only
one way. If the plug does not fit fully into the extension
cord, reverse the plug. If the plug still does not fit,
obtain a correct polarized extension cord. A polarized
extension cord will require the use of a polarized wall
outlet. This plug will fit into a polarized wall outlet only
one way. If the plug does not fit fully into the wall out-
let, reverse the plug. If the plug still does not fit, con-
tact a qualified electrician to install the proper wall out-
let. Do not change the unit plug, extension cord recep-
tacle, or extension cord plug in any way.
o Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for this unit. Receptacles are available having
built-in GFCI protection and may be used for this mea-
sure of safety.
CORD SETS: Make sure your cord set is in good con-
dition. When using a cord set, be sure to use a cord
that is heavy enough to carry the current that your unit
will draw. An undersized cord set will cause a drop in
line voltage resulting in loss of power and overheating.
The table shows the correct size to use depending on
the cord length and nameplate amperage rating. If in
doubt, use the next heavier size line gauge. The small-
er the gauge number, the heavier the cord. To reduce
the possibility of disconnection
of the unit cord from
the cord set during operation, see Fig. 9.
A nameplate on your unit indicates what voltage it
uses. Never connect the unit to an AC voltage that
differs from this voltage.
MINIMUM
WiRE SiZE FOR EXTENSION CORDS FOR
120 VOLT APPLIANCES
USING 0=6 AMPS
Cord length (ft)
25
50
Wire size (AWG)
16
16
100
16
150
14
Inspect all extension cords and the unit power
connection periodically.
Look closely for deterioration,
cuts or cracks in the insulation. Also inspect the
connections for damage. Repair or replace the cords
if any defects appear.
Avoid dangerous environments.
Never operate your
unit in damp or wet conditions. Moisture is a shock
hazard.
o Do not use the unit in the rain.
Do not handle the plug or the unit with wet hands.
BEFORE
OPERATING
Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
o All guards and safety attachments
must be installed
properly before operating the unit.
Inspect the unit before use. Replace damaged parts.
Make sure all fasteners are in place and secure.
Replace parts that are cracked, chipped, or damaged
in any way. Do not operate the unit with loose or
damaged parts.
Use only 0.080 in (2.03 mm) diameter genuine
Craftsman ®replacement
line. Never use
metal-reinforced
line, wire, or rope, etc. These can
break off and become a dangerous projectile.
o Be aware of the risk of injury to the head, hands and
feet.
Clear the area to be cut before each use. Remove all
objects such as rocks, broken glass, nails, wire, or
string which can be thrown or become entangled in
the cutting attachment.
Clear the area of children, bystanders, and pets. At a
minimum, keep all children, bystanders and pets
outside a 50 feet (15 m.) radius; there still may be a
risk to bystanders from thrown objects. Bystanders
should be encouraged to wear eye protection.
If you
are approached, stop the motor and cutting attach-
ment immediately.
Before each use, check that the cutting head is
correctly fixed and that the trigger returns automatical-
ly to the off position.
-3-
Advertisement
Table of Contents
