Advertisement
8. Remove nut at top of smk strajner
Remove
extenslo"
pipe
C.
Loosen the large-diameter
nut at the base
of rhe strainer by placlng
the tip of a
screwdriver
on rhe ridge of the nut and
gently rappIng
[he scrwdwer
with a
hammer
8
Attach the
upper
mounfiqg
assembhi.
A Working
from under sink, slip the &ond
rubber
gasket, then the metal back-up
ring
(flat side up), up and over sink flange
D. Remove nut
E.
Push the strainer assembly
up through
the
sink hole and remove
5
Clean sink's
drain line.
If installing
m a new
home,
go to Step 6.
Remove dram trap. U&ng an auger. clean out
the howont.
drain pope that runs from the
trap to the ma," waste pope.
6
Separate the
mounting
assembly.
A
Holdmg
rhe mcuntlng
assemblywth
one-
hand, use the other hand to ~nsenjam-
breaker wench
Into one of the lugs of the
lower mounting
ring Turn assembly
counter-
clockwise
and rerno4.
B. Loosen screw-i on mount,ng
assembly
until
they are lwel wth
mou"t,ng
ring surface
c. Use screwdriver
to pry off snap r,ng
D.
Take assembly
apart and set aslde
7
Apply rubber
s
asket or putty
o sink flange. ,-,
A
The rubber
sink flange gasket should always
be used where
powble
Place rubber
gasket over sink flange Go to Step J-C
B. If sink opening
does not pemxt
the use of a
rubber
seal. plurhber's
putty may be used
Form puty
Into a long roll by rolllng It
between
your hands
Press roll under sink
flange r\m
c.
Place flange Into sink drain hole Push down
genrly but firmIx to make sure flange SltS
evenly over gasket cn in purry
PANEL B
a. Holding
[he rubber gasket and metal back-
up r,"g I" place, atlach the mo"nt,"g
r,"g to
the sleeve with the three mounting
ring
scr-
Do Not rIghten scre*ys at thts tome
C. Push rubber
gasket, metal back-up
ring and
mo"nt,"g
mg funher up sink slewe
Slide
snap ring onto sink slewe
until It pops Into
place I" the sleeve groove
D.T~ghten
mount,ng
SC,-
until entlre
moumng
assembly
IS seated evenly and
tightly agamst sink
D.
9
Make
electrical
connections.
A
Remove elecmcal
plate from the bottom
of the "ewd~sposer
Pull out the blackand
wtwe
elecb~cal wres.
Locate the green
grounding
screw under plate
B. Insert strain relief mto hole Insert power
supply cable throuqh
strain relief Pull cable
w,res rhrough
ope&g
where disposer
WIRS are located
Tighten stral" relief
SClW.5
connect rhi
to white, and black to
I
--rm
black.
wrap
wire ConnectIons
wlrn
elecmcal
tape
Put wres
back inslde
disposer
housIng
Notez
This appliance
15
equlpwd
wlt3? copper
lead wires
If
connectlo"
1s made to aluminum
house
wmng,
use only speoal
connectors
wixch
are approved
for,o,nmg
copper
to
alumrum
wires I" accordance
with tie
natlonal
electrical
code and local codes
and ora~nances
Improper COnneCtlon of the equlpment~grcundlng
conducta
!
can result w electrical shock. oer~~l
~nfuw o( &am
:
Electrical
ground
is required
on this
appliance.
'90 NOT reconnect
electrical
current
to
main service
panel
until
proper
ground
IS r.sMled.
A.lf
the cabls
leading
to the disposer
has
three
wires,
attach the green grounding
wire to the green grounding
screw Go to
S'ep 10-D
Advertisement
