Advertisement
Available languages
Available languages
18.Checkthattheextenstons a reparallel a ndeven
with.or slightly below, t he topof thetable.
19.[A
}
[,,_ WARNINGj In nocasearethe extensions
to be higherthan.or above,thetopof thetabletop
or elsetheymayinterfere withtheworkpiece during
routing. T hiscouldcausea condition thatcanresult
in possible seriousinjury.
20. If theextensions a rehigherand/ornotparallel.
thenloosenthefasteners holding theextensions t o
thebraces andto thetabietop.andreposition them
untiltheyare parallel.
2I. SECURELY T IGHTEN ALLFASTENERS AGAIN.
22.Todoublecheck,slidea flatpieceofwoodalong
top oftheroutertablein alldirections. Makesure
thattheedgeof thewoodmovesfreelywithoutcon-
tactingtheedgesofthe extensions.
PUSH BLOCK
1.Thread thesmallendoftheclamprodintothe
threaded holein theclampplateuntilthe rodbottoms
outsecurely against t heplate,as shown in Figure11.
2. Makesurethatthe pushblockis orientedso that
the 'C onthe clampplateFACES OUTWARD, as
shownin Figure1t.
FIGURE
11
"'22!DX:'":
27
'
"'4
--
--<
.'.a3--_-=__'_
2_-". '= -*':._.TE -2--2".'£
,..
Z--
:_-" NST -:_:::EE
T_
C-
_='_
",G
LQC*
.'._-S-E:--
,,,<,;
t4
2_. -E'(
MACH:X-_-
SCREW
NUT
3. Assemble
the 1,/4'. I.D. x 1/2" O.D. x 3/64"
thick
spring
lock washer
and 1 4-28 hex machine
screw
nut to clamp
rod. as shown
in Figure
11.
4. Securely
TIGHTEN
the nut on the clamp
rod.
5. Insert the other
end of the clamp
rod through
the
hole in the push
block. Make
sure the orientation
of
the push block is as shown
in Figure
11.
6. Assemble
11/32" I.D. x 11/16" O.D. x 1/16" thick
washer
and the 5/16-18
wing nut to the clamp
rod as
shown
in Figure
11.
7. It is not necessary
to tighten
the wing nut. The
clamp
rod should
rotate
freely
in the push block.
{,_WARNING
The v{brations
from operating
the
router
can, from time to t_me. cause
the hex machine
screw
nut and the clamp
plate
to become
loose on
the clamp
rod. PERIODICALLY
CHECK
THESE
FASTENERS
AND ALL FASTENERS
to ensure
that
they are tight and secure
FENCE
1. Assemble
the adjustable
jointing
fence to the
router table fence
using a 1'4-20
x 1" long hex cap
screw,
a 9'32"
I.D
x 34
O.D.
x 1 16" thick washer.
and the adjustab!e
fence
clamping
knob. as shown
in
Figures
12a and
12b
The V-guide
on the adjustable
jointing
fence will mate
with and slide on the V-guide
in the router table fence.
2. Push the adjustable
jointing
fence into the router
table fence as far as _twill go and tighten the clamp-
ing knob.
FIGURE 12a
/
/
'&_-7
a7.
_-a_LE
FIGURE
12b
"z2CX:
',
\
,,' \
,
/
_'
_Z'.-'.S
=£',7B
o-
_"_,
ROU*_Eq
TABLE
_
FEr;CE
L >_
[-:'.'=
',G
-',i-
'
'
_B
7_
Z"
.'.ZB"_ER
3, Assemble
the fence guide
to the bottom
of the
fence
using #10-32
x 7/8" long panhead
machine
screws
and #10-32
hex "KEPS"
nuts. as shown in
Figure 13. (The nut portion
of the hex "KEPS"
nut fits
into the recess, with the washer
portion
out of the
recess.)
DO NOT TIGHTEN
the fasteners
at this time.
11
Advertisement
