Craftsman EZ3 917.258562 Owner's Manual page 12

OPERATION
]
71
The operation of any tractor can result in foreign objects thrown into the eyes, which can /
result in severe eye damage. Always wear safety g|asses or eye shields while operating your
/
tractor or performing any adjustments or repairs. We recommend a wide vision safety mask
over the spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 8)
Your tractoris equipped with an operator presencesensing
switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
.Depress clutch/brake pedal into full "BRAKE" position
and hold.
Place parking brake lever in =ENGAGED"position and
release pressure from clutch/brake pedal. Pedal should
remain in "BRAKE" position. Make sure parkingbrake
will hold tractor secure.
THROTTLE
CONTROL
ATTACHMENT CLUTCH LEVER
"ENGAGED" POSITION
CHOKE "DISENGAGED"
CONTROL POSITION
PARKING BRAKE
"BRAKE"
POSITION POSITION
GEARSHIFT
LEVER
"D_SENGAGED"
POSITION
CLUTCH_RAKEPEDAL
"DRtVE"POS|TION
HEIGHT ADJUSTMENT KNOB
FIG. 8
I
CAUTION: Always stop tractor com- |
pletely, as described above, before leav-
1
ing the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL
(See Fig. 8)
Always operate engine at full throttle.
Operating engine at less than full throttle reduces the
battery charging rate.
Full throttle offers the best bagging and mower perfor-
mance.
TO USE CHOKE CONTROL (See Fig. 8)
use choke controlwheneveryou are starting a coldengine.
Do not use to start a warm engine.
To engage choke control, puUknob out. Slowly push
knob in to dise{lgage.
TO MOVE FORWARD AND BACKWARD
(See Fig. 8)
The direction and speed of movement iscontrolledby the
gearshift lever.
Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position.
Move gearshift and range shift levers to desired posi-
tion.
Slowly release clutch/brake pedal to start movement.
IMPORTANT; BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SOW]LL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE,
STOPPING (See Fig. 8)
MOWER BLADES -
Move attachment clutch lever to "DISENGAGED" po-
sition.
GROUND DRIVE -
Depress clutch/brake pedal into full "BRAKE"position.
Move gearshift lever to neutral (N) position.
ENGINE -
Move throttle control to slow (.,gll.) position.
NOTE: Failure to move throttle control to slow (,gll.)
position and allowing engine to idle before stopping may
cause engine to "backfire".
Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
Never use choke to stop engine.
HOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass areas. 12
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 8)
The cuttingheightiscontrolledby turningthe heightadjust-
ment knob in desired direction;
Turn knob clockwise(,.r_) to raise cutting height.
Turn knob counterclockwise (_) to Iowercutting
height.
The cutting height range is approximately 1-1/2" to 4"+The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
The average lawn shouldbe cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
For best cutting performance, grass over 6 inches in
height should be mowed twice. Make the first cut
relatively high; the second to desired height.