Oki GL408e Install Manual
Wlan card install guide
Hide thumbs
Also See for GL408e:
- Install manual (13 pages) ,
- Manual (8 pages) ,
- Install manual (11 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Manual
Advertisement
Table of Contents
Related Manuals for Oki GL408e
Summary of Contents for Oki GL408e
- Page 1 WLAN CARD INSTALLATION GUIDE For printer models: 4xxe Series Read this Installation Guide before and during the installation of the above accessory. Keep this Installation Guide handy for future reference.
-
Page 2: Limitation Of Liability
WLAN Card Installation Guide 1 General 1.1 Important information This quick guide provides important information on how to setup your new SATO product. Be sure to read this quick guide thoroughly before using this printer. It is an integral part of the product and should be kept in the immediate vicinity of the device and available to the operating staff. -
Page 3: Explanation Of Symbols
WLAN Card Installation Guide 1.3 Explanation of symbols This instruction manual uses various warning icons to help you understand the safe operation of your printer. Explanations of the icons are below. WARNING! Indicates neglectful or erroneous use may cause irreparable damage to the product, serious injury to the operator, or worse. -
Page 4: Sato Group Of Companies
WLAN Card Installation Guide Contact and Document Information SATO GROUP OF COMPANIES International Headquarters Americas SATO INTERNATIONAL PTE. LTD SATO INTERNATIONAL AMERICA, INC. 438A Alexandra Road #05-01/04, (Regional HQ) Alexandra Technopark, Singapore 119967 10350 Nations Ford Road Suite A, Charlotte, NC 28273 Phone: 65-6271-2122 Fax : 65-6271-2151 Email: sales@sato-int.com Phone: 1-704-644-1650 Fax: 1-704-644-1662... - Page 5 WLAN Card Installation Guide GL4xxe Wireless LAN Card Installation Before installing the WLAN card, make sure the printer is OFF and disconnected from the power supply. Make sure you have discharged any static electricity (by touching a grounded component on the printer). 1.
- Page 6 WLAN Card Installation Guide GL4xxe Wireless LAN Antenna Installation After installing the LAN card, you will install the antenna for transmission and reception of signals. 1. Screw the antenna into the connector on the WLAN card. (Fig 2a) Figure 2a. Installing the WLAN antenna 2.
- Page 7 WLAN Card Installation Guide WIRELESS LAN CARD INTERFACE SETUP Once the WLAN card is installed, you can access the Ethernet settings in the GL’s Interfaces Mode menu. An overview of the WLAN options is listed below: POWER ONLINE INTERFACES INTERFACES Host Interface* Host Interface* LINE...
- Page 8 WLAN Card Installation Guide WLAN Card Installation Guide Menu screen What the options mean INTERFACES Permits entry into the INTERFACES Mode. Is the menu selection screen for the INTERFACES Mode. INTERFACES Ignore CR/LF Item No. Check BCC Check History Buffer Comm.
-
Page 9: Ethernet Setting
WLAN Card Installation Guide Menu screen What the options mean Communication Protocol. Selects the mode of Bi-Directional communications. In most cases this menu does not need to be altered and is meant to help support legacy applications which may have incorporated older bi-directional statuses. Anything other than Staus 5 or Standard (none) is not recommended. -
Page 10: Ethernet Port
WLAN Card Installation Guide Menu screen What the options mean Determines how the printer and/or NIC card respond when a job has been completed. The definition of a complete job is also determined by this setting. • Standard - factory default. The NIC card responds to the host that the job is complete when the entire print job has been accepted by the printer. -
Page 11: Wlan Setting
WLAN Card Installation Guide Menu screen What the options mean This menu allows the Subnet Mask for the TCP/IP protocol to be set in four three-digit segments (SEG1 through SEG4). If the Subnet Mask is assigned by Bootp, ARP, or DHCP, it is dynamic and read only. - Page 12 WLAN Card Installation Guide Menu screen What the options mean Allows selection of the way the wireless option communicates. • Infrastructure - factory default. The wireless option must go through an access point. Operation Mode • Pseudo IBSS - uses a proprietary, peer-to-peer communication without an access point. The Infrastructure * two peers must be specific to one manufacturer.
- Page 13 WLAN Card Installation Guide Menu screen What the options mean Power Management. This menu allows the power-save and sleep modes to be set. The value set wil be in milliseconds. If set to zero, the power-save mode will be disabled. Power Mgt The allowable range is 0 to 1000 ms., and the factory default is 0 ms..
- Page 14 WLAN Card Installation Guide...