Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Craftsman 335.25187
Summary of Contents for Craftsman 335.25187
- Page 1 Owner's Manual CRFIFTSMFIN ° DELUXE ROUTER PANTOGRAPH Model No. 335.25187 Caution: • Safety Before using this product, • Assembly read this manual and follow ° Operation all its Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179 15881 REV 4/00...
- Page 2 Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Personal Safety Keep your work area clean and well lit. Stay alert, watch what you are doing and use Cluttered benches and dark areas invite common sense when operating a power tool.
- Page 3 in the hands of untrained users. Service Tool service must be performed only by Maintain tools with care. Keep cutting tools qualified repair personnel. Service or sharp and clean. Properly maintained tools, with maintenance performed by unqualified personnel sharp cutting edges are less likely to bind and could result in a risk of injury.
- Page 4 ASSEMBLY REAR PIVOT REAR TUBE ASSEMBLY Locate the REAR TUBE ASSEMBLY PROJECT,.G P'N / and remove the two PIVOT CAPS LOCATING HOLE _ ', which are not holding a tube. With set of (3) HOLES up, place the end of the OU,DEA.M SCREWS/\ GUIDE...
- Page 5 REAR SUPPORT SCREWS 6. Screw a 3/8-16 HEX NUT on both OT BOLTS of the REAR SUPPORT SCREWS. Assemble both screws through the REAR PIVOT BOLTS until the ball protrudes 1/2", Snap SLIDE BUTTON on ball of screw which is on guide arm side, (FIG.
- Page 6 11. Adjust support screw on guide corner until guide arm is parallel. Now left side tube guide arm are parallel to work bench. Secure place with nut. 12. Square pantograph frame so corners are at 90 ° . Fasten hold down socket to work surface through three holes.
- Page 7 MAKING SIGNS USING CAPITAL LETTERS "Modern Writing Style" 16. Locate stencil of first letter against inside fold of stencil cover and up f F, against tack. (Locating each stencil the same results in straight work.) Be sure cutter bit is on center of work SPACING board when stylus...
- Page 8 21. Remove stencil just routed and locate next stencil in place. (Leave cutter in groove.} 22. Loosen work piece and move work piece felt until stylus is on __SHADED AREA STARTING POINT. Reclamp work piece. Switch router on and proceed. (Repeat until sign is completed.) OTHER FOUR STYLES rout a sign using "Old...
- Page 9 THREE DIMENSIONAL ENGRAVING 25. After selecting a pattern you will need a work piece thick enough to accept engraving plus 1/4" 1/2". PLASTER PATI'ERN FINISHED ENGRAVING (Redwood is very easy to rout.) SUPPORT SCREW Maximum pattern size you can use is 1 1/4"...
- Page 10 EASY DOES IT ENGRAVINGS Start routing at the highest point-and 30. After reading helpful hints you are work your way down to the lower ready to rout a 3D sculpture. places, Avoid leaving tall thin sections 6" x 6" pattern will take a couple because they will chip away easily.
- Page 11 For in-home major brand repair service: Call24 hours a day, 7 days a week 1-800-4-1VIY-HOME s M(1-800-469-4663) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 In Canada for all your service and parts needs call -1-800-665-4455 Au Canada pour tout le service ou les pi_ces Forthe repair or replacement parisyou need: Call 6 am - 11 pm, 7 days a week PartsDirect sM...