Cub Cadet 1527 Operator's Manual page 12

SeatAdJustment Lever
To adjust the seat forward or backward, slide the seat
adjustment lever to the left and reposition the seat to
the desired position. Once a comfortable position is
found, release the seat adjustment lever to lock the
seat in place. Refer to SeatAdjustmenton page 17 of this
manual for more detailed instructions.
DeckLiftLever
Found on your tractor's right fender, the deck lift lever is
used to change the height of the cutting deck. To use,
move the lever to the left, then place in the notch best
suited for your application.
SECTION 5: OPERATING Y OUR LAWN
WARNING
AVOID SERIOUS INJURY ORDEATH
• GO UP AND DOWN SLOPES, NOT ACROSS.
• AVOID SUDDEN TURNS.
• DO NOT OPERATE THE UNIT WHERE {T COULD SLIP OR TIE
• IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK
DOWNHILL SLOWLY.
• DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.
• NEVER CARRY CHILDREN, EVEN WITH BLADES OFP
• LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.
• KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES) IN
PLACE AND WORKING.
• REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADE(S).
• KNOW LOCATION AND FUNCTION OF ALL CONTROLS.
• BE SURE BLADE(S) AND ENGINE ARE STOPPED BEFORE PLAC-
ING HANDS OR FEET NEAR BLADE(S).
• BEFORE LEAVING OPERATOR'S POSITION, DISENGAGE
BLADE(S), ENGAGE BRAKE LOCK, SHUT ENGINE OFF AND
REMOVE KEY.
READOPERATOR'SMANUAL
,_ WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
SafetyInterlock Switches
This tractor is equipped with a safety interlock system
for the protection of the operator. If the interlock system
should ever malfunction, do not operate the tractor.
Contact a Cub Cadet dealer. The safety interlock
system prevents the engine from cranking or starting
unless the parking brake is engaged, and the PTO knob
is in the disengaged (OFF) position.
The engine will automatically shut off ifthe operator
leaves the seat before engaging the parking brake.
The engine will automatically shut off ifthe operator
leaves the tractor's seat with the PTO knob in the
engaged (ON) position, regardless of whether the
parking brake is engaged.
The electric PTO clutch will automatically shut off if
the PTO knob is moved into the engaged (ON)
position with the drive pedal in position for reverse
travel.
TRACTOR
_, WARNING: Do not operate the tractor if the
interlock system is malfunctioning. This
system was designed for your safety and
protection.
SettingtheGauge Wheels
Select the height position of the cutting deck by placing
the deck lift lever in any of the six different cutting height
notches on the right fender.
To adjust the deck wheels so that they are between ¼-
inch and ½-inch above the ground as follows.
_, ARNING: Keep hands and feet away
from the discharge opening of the cutting
deck.
NOTE:
The deck wheels are an anti-scalp feature of
the deck and are not designed to support the weight of
the cutting deck.
Place the tractor on a firm and level surface, preferably
pavement, refer to Figure 7, and proceed as follows:
Place the tractor's deck lift handle in the normally
desired mowing height setting, then check the
gauge wheels for contact or excessive clearance
with the surface below.
If the wheels contact the surface adjust as follows:
a. Raise the deck lift handle to its highest
setting.
b. Remove the reargauge wheels by removing
the lock nuts and shoulder screws that
secure them to the deck.
c. Remove the lock nuts and shoulder screws,
that secure the front gauge wheels to the
deck.
d. Place the deck lift handle in the desired
mowing height setting.
e. Insert the shoulder screw with the rear gauge
wheel into the index hole that leaves
approximately 1/2" between the bottom of
the wheel and the pavement.
f. Note the position of the index hole used; then
install the other rear gauge wheel and the
front ball wheels into the corresponding index
hole of the other gauge wheel brackets.
12