Related Manuals for Equator SB 818
Summary of Contents for Equator SB 818
- Page 1 EQUATOR SERVICE MANUAL SPARE PARTS CATALOG First Edition - March 2005 18" DISHWASHERS MODEL: WB 818 SB 818 www.EquatorOnline.com Advanced Appliances...
-
Page 2: Table Of Contents
SPECIFICATIONS SCHEMATIC DIAGRAM WIREING DIAGRAM TIMER CYCLE CHART COMPONENT OPERATION AND REPAIR Safety Precautions Timer ……………………………………………………………………7 Door Latch and Switch Assembly…………………………………… 8 Float Switch Assembly PRODUCT EXPLODED VIEWS TROUBLESHOOTING CONTENTS ……………………………………3 ……………………………… 4 ……………………………………5 ………………………………… 6 …………………………………………… 7 …………………………………………… 8 …………………………………10 ……………………………………………... -
Page 3: Specifications
MODEL Rating Motor (HP) Motor (Amps) Heater Wattage Wash Total Amps (Load Rated) Thermostat Contacts Close at Suggested Min. Incoming Temperature Pressure (PSI) Minimum/Maximum Connection (NPT) Consumption (Toil Gallons) Water Valve Flow Rate (GPM) SPECIFICATION ELECTRICAL 120V 60Hz 1000W 9.2A ±5 °F ±3... - Page 4 Schenmatic Diamgram of Dishwasher (WQP8-9223 and WQP8-9324) AC110/120V 50/60Hz 7805 ITR(78)
- Page 5 Wiring Diagram of Dishwasher (WQP8-9223 and WQP8-9324) gray gray yellow gray white white green green ITR(78) pink green AC110/130V 50/60Hz 7805 white white white pink black black gray gray...
-
Page 6: Schematic Diagram
With the circuit board, user selects the various cleaning cycles of the dishwasher with press the button. The circuit board controls all the electrical functions of the dishwasher in all stages of each cycle. All functions can be traced on the chart. Diagram provided in this service manual. -
Page 7: Door Latch And Switch Assembly
DOOR LATCH AND SWITCH ASSEMBLY The latch and switch are located in the door assembly behind the control panel. The dishwasher will not operate until the door is closed; the latch engages the door catch. To Test Or Replace Door Switch. -
Page 8: Float Switch Assembly
4. Install new door latch assembly and reverse procedures to complete repairs. FLOAT SWITCH ASSEMBLY The water float assembly is located in the right lower side of the dishwasher (the portable located behind the lower front crosspiece). When too much water enter the dishwasher，the water will enter the float support through the overflow pipe,... - Page 9 Figure 7 Figure 8 To Remove Or Replace Float Switch 1. Disconnect dishwasher from electrical supply. 2. Remove electrical leads to float switch. 3. Take down the switch from float support. 4. Install new float switch and reverse procedures to complete repairs (See...
-
Page 10: Troubleshooting
TROUBLESHOOTING The troubleshooting cheek list is common for all dishwasher models. They use different parts to accomplish the same thing and diagnosis will remain similar. When a problem arises, and a possible cause is listed, follow the test, remove or replace procedures as outline in this service manual. - Page 11 Dishwasher does ●Check circuit for power ,check if advance automatically. the wire misconnected. ●Have wire cut off ●Water supply turns off. Dishwasher will not fill with ●Defective inlet valve. water. ● obstructions. ●Defective float switch. ●Damaged circuit board. ●Wiring (broken or burnt).
- Page 12 ● Overcharge of water. ●Tub seal (torn, worn or loose). ● Dishwasher properly. ●Dishwasher is not level. ● Overburden detergent). ●Hose clamps loose. ● Heater element mounting nuts loose. ●Water seal leaking. ●O-ring is not in position. ● Motor and pump assembly not seated proper in tub liner bottom.
- Page 13 ●Pump parts not properly installed. ●Debris in bottom of tub sump area. ●Defective motor bearings. ● Something Dishwasher continues to fill or continues to fill even material) under diaphragm in water though in case of there is no inlet valve.