Cub Cadet Ex SERIES Installation & Owner's Manual
  1. Manuals
  2. Brands
  3. Cub Cadet Manuals
  4. Automobile Parts
  5. Ex SERIES
  6. Installation & owner's manual
Cub Cadet Ex SERIES Installation & Owner's Manual

Cub Cadet Ex SERIES Installation & Owner's Manual

Cab kit with hard doors and soft rear curtain p/n 59a40058727
Hide thumbs
Table of Contents

Advertisement

Quick Links

CUB CADET Ex SERIES
cab kit with hard doors
and soft rear curtain
p/n 59A40058727
An optional Hard Rear Panel
can be purchased separately.
The contents of this envelope are the property of the owner.
Be sure to leave with the owner when installation is complete.
APPROXIMATE INSTALLATION TIME: 2 to 3 HOURS
Shown with optional work lights and optional sliding windows in doors.
Additional options available are: heater, hard rear panel, and rear window wiper.
Note: a front windshield wiper comes standard with this cab kit.
(excluding accessories)
Rev. -, p. 1 of 15
(revised: 10/23/2008)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ex SERIES and is the answer not in the manual?

Questions and answers

Related Manuals for Cub Cadet Ex SERIES

Summary of Contents for Cub Cadet Ex SERIES

  • Page 1 CUB CADET Ex SERIES Rev. -, p. 1 of 15 cab kit with hard doors and soft rear curtain p/n 59A40058727 An optional Hard Rear Panel can be purchased separately. The contents of this envelope are the property of the owner.

  • Page 2: Helpful Hints

    Rev. -, p. 2 of 15 NOTICE Cabs, blades, and general accessories add additional weight to the base vehicle. Deduct the accessory’s total weight from the vehicle’s rated capacity including driver and passenger. Exposure to Carbon Monoxide can Cause illness, serious injury or death.
  • Page 3 Rev. -, p. 3 of 15 VEHICLE PREP Per fig. 1.1, remove the left and the right grab remove both handles from the fenders. Bolts are underneath the fend- grab handles ers. These grab handles will not be re-installed. Per fig. 1.2, temporarily remove both rear flasher lights.

  • Page 4: Side Frames

    Rev. -, p. 4 of 15 ROLL BAR BRACKETS (cont’d.) Per figures 2.2 and 2.2.1, loosely assemble the roll bar bracket and the roll bar mount around the ROPS tub- ing as shown (with the slots outboard and the vibration mount against the front facing surface of the ROPS tub- ing).
  • Page 5 Rev. -, p. 5 of 15 SIDE FRAMES (cont’d.) Place the side frame onto the tractor making sure metric hex bolt and that the contour bulb rubber that sits on the fender is all 5/16” steel washer here pointing outboard. Per fig. 3.3, install the M8 bolt and washer through the rear inboard mounting tab then through the 1/4”...
  • Page 6 Rev. -, p. 6 of 15 HARD REAR PANEL (cont’d.) Attach the rear legs shown in fig. 4.3 to the back top of hard sides of each of the side frames making sure the vibration rear panel mount and the bent flange are both on the outboard side of the cab enclosure.
  • Page 7 Rev. -, p. 7 of 15 6. COWL 6.1 Per fig. 6.1, install the cowl with the bent flanges up top and towards the inside of the cab. Bulb rubber to all be pointing outward as shown. 6.2 Per fig. 6.2, use the following hardware per side: in the very top hole, use one 5/16-18 button head bolt, two steel washers, and one locknut.
  • Page 8 Rev. -, p. 8 of 15 8. ROOF 8.1 If installing an optional hard rear panel, remove the six soft rear curtain snaps pre-assembled onto the back surface of the roof. Discard the snaps. 1” long bolt here 8.2 Use a Phillips head screwdriver to punch a hole through the headliner at all of the covered bolt hole loca- tions (10 places).
  • Page 9 Rev. -, p. 9 of 15 SOFT REAR CURTAIN If not installing a soft rear curtain, skip to step 10 below. Snap the rear curtain (see fig. 9.2) to the factory installed snaps on the inside surface of the back of the roof (6 snaps).
  • Page 10 Rev. -, p. 10 of 15 11. FRONT VINYL FILLERS 11.1 Fig. 11.1 shows the difference between the left and right fillers. Install each filler to the bottom inside sur- face of the front metal cowl and to the inside surface of the side frame tubing.
  • Page 11 Rev. -, p. 11 of 15 13. SMV SIGN 13.1 Per fig. 13.1, install the black SMV bracket to the fender oriented as shown. Use the following hardware: one 5/16-18 x 3/4” long button head bolt, two steel wash- ers, and one locknut. Locknut to be underneath the fender.
  • Page 12 Rev. -, p. 12 of 15 14. DOORS 14.1 Apply grease to the pin hinges. With assistance, re- install the doors onto the pin hinges. Work the doors back and forth until the hinges are completely seated. Specific adjustments can be made per steps 14.2 and 14.3. Note: top of door should end up visually parallel with side of roof.

  • Page 13: Finishing Touches

    Rev. -, p. 13 of 15 16. FINISHING TOUCHES filler bolts with 16.1 Install the gas shock to the frame and door with the soft rear curtain small piston end towards the door. Press the button on the installation compression fastener to lock the gas shock to the ball stud. 16.2 Install the supplied 5/16”...

Table of Contents