Advertisement
Quick Links
CUB CADET Sc SERIES
cab kit with hard doors
and soft rear curtain
p/n 59A40056727
An optional Hard Rear Panel
can be purchased separately.
The contents of this envelope are the property of the owner.
Be sure to leave with the owner when installation is complete.
APPROXIMATE INSTALLATION TIME: 2 to 3 HOURS
Shown with optional work lights and optional sliding door windows.
Additional options available are: heater, hard rear panel, and rear window wiper.
Note: a front windshield wiper comes standard with this cab kit.
WARNING: FOR STABILITY,
A 100 POUND BALLAST
WEIGHT IS REQUIRED IN
REAR BALLAST BOX.
(excluding accessories)
Rev. -, p. 1 of 19
(revised: 10/23/2008)
Advertisement
Related Manuals for Cub Cadet Sc Series
Summary of Contents for Cub Cadet Sc Series
- Page 1 CUB CADET Sc SERIES Rev. -, p. 1 of 19 cab kit with hard doors and soft rear curtain p/n 59A40056727 An optional Hard Rear Panel can be purchased separately. The contents of this envelope are the property of the owner.
-
Page 2: Helpful Hints
Rev. -, p. 2 of 19 NOTICE Cabs, blades, and general accessories add additional weight to the base vehicle. Deduct the accessory’s total weight from the vehicle’s rated capacity including driver and passenger. Exposure to Carbon Monoxide can Cause illness, serious injury or death. Never operate vehicle if suspicious of Carbon Monoxide. - Page 3 Rev. -, p. 3 of 19 VEHICLE PREP. Per figures 1.1 and 1.1.1, use a flat screwdriver and pliers to remove three (3) plastic pine tree clips from the rubber mat on top of the floorboard on each side of the tractor.
- Page 4 Rev. -, p. 4 of 19 VEHICLE PREP. (cont’d.) Per figures 1.3 and 1.3.1, remove two (2) M12 bolts from the bottom front area of the ROPS structure as shown. Repeat for opposite side of tractor. Discard all four bolts. New, longer hardware is supplied. Per fig.
- Page 5 Rev. -, p. 5 of 19 notch to point forward REAR MOUNT BRACKET Per fig. 2.1, install the right side rear mount bracket as shown with the notch pointing forward. Use the two new, longer M12 bolts supplied. Leave bolts loose.
- Page 6 Rev. -, p. 6 of 19 WINDSHIELD SUPPORT Per fig. 4.1, install the windshield support to the top front corner of the side frames. Orient the windshield support so the bent flanges are down and the decals are legible. Use the following hardware in the lower hole on each side (note: the remaining holes will receive hard- ware when the roof is installed): one 5/16-18 x 3/4”...
- Page 7 Rev. -, p. 7 of 19 ROLL BAR BRACKET If installing an optional hard rear panel at this time, skip to step 7 on the next page. (Note: the steel rear mount shown in fig. 6.2 is not used with the optional hard rear panel).
- Page 8 Rev. -, p. 8 of 19 OPTIONAL REAR LEGS Per fig. 7.1, install the supplied rubber vibration bent flanges mount to the rear leg using the following hardware: 1/4- are shown 20 x 1” long button head bolt, one steel washer, and one up in this view locknut.
- Page 9 Rev. -, p. 9 of 19 9. WINDSHIELD 9.1 See fig. 9.1. Have the following items ready: four sandwich the 5/16-18 x 1 3/4” long flat head bolts, 4 steel washers, 4 plastic spacer locknuts, and 2 plastic spacer blocks. With assistance, block here install the windshield hinges to the windshield support with the two spacer blocks between the hinge and the...
- Page 10 Rev. -, p. 10 of 19 11. TIGHTEN ALL BOLTS 11.1 Before and during bolt tightening, measure and offset the side frames symmetrical to the ROPS tubing on the rear of the tractor. Shift and/or push cab as necessary before tightening all bolts. Tighten all bolts including those under the floor mats, etc..
- Page 11 Rev. -, p. 11 of 19 13. VINYL FILLERS (qty.: 4) seat shown tilted up 90 degrees 13.1 Per fig. 13.1, raise the seat and install the smaller of the two rectangular vinyl fillers as shown. Note: the slightly larger rectangular filler is for the air intake shield.
- Page 12 Rev. -, p. 12 of 19 13. VINYL FILLERS (cont’d.) velcro the 13.4 Install the filler to suit. Note: the narrow front por- left onto tion pointed out in fig. 13.3.2 has mating velcro strips for the right connection onto each other for closure. Note: the rear portion of this filler will either connect to the bottom of a soft rear curtain or an optional hard rear panel as the in- stallation continues.
- Page 13 Rev. -, p. 13 of 19 13. VINYL FILLERS (cont’d.) 13.6 Orient the filler so the pocket for the fuel fill cap is on the left side where required. Per figures 13.6 through 13.6.3, apply narrow 5/8” wide PSA hook velcro to the very bottom horizontal edge of the air intake position the shield.
- Page 14 Rev. -, p. 14 of 19 13. VINYL FILLERS (cont’d.) 13.7 Per fig. 13.7, apply narrow 5/8” wide PSA hook velcro along four sides of the rectangular air flow open- ings as shown. 13.8 Per fig. 13.8, install the final rectangular filler over the air flow openings onto the newly installed vel- velcro all around perimeter cro.
- Page 15 Rev. -, p. 15 of 19 15. DOORS 15.1 Apply grease to the pin hinges. With assistance, re- install the doors onto the pin hinges. Work the doors back and forth until the hinges are completely seated. Specific adjustments can be made per steps 15.2 and 15.3. Note: top of door should end up visually parallel with side of roof.
- Page 16 Rev. -, p. 16 of 19 17. FLASHER LIGHT BRACKET 17.1 Per fig. 17.1, install the flasher light brackets using the following hardware per side of the tractor: one 5/16-18 x 3/4” long button head bolt, two steel washers, and one lock- nut.
-
Page 17: Care And Maintenance
Rev. -, p. 17 of 19 18. FINISHING TOUCHES (cont’d.) 18.4 If a soft rear curtain has been installed, install the fol- lowing hardware into the factory installed threaded inserts in the back of each of the side frames: four 5/16-18 x 3/4” long button head bolts, four plastic washers, and four steel wash- ers.