Advertisement
This page provides an overview
of the TV configuration.
See the pages listed
below for more
specific,
detailed
instructions
at each step; how to access and use the Installer
menu etc.
*Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Program
(Channel search) is disabled if there is an Aux input active.
*Note 2: Under certain conditions, changes to the input mode of the RGB
inputs will not take effect until the power is cycled (TV is turned OjOC a nd On).
To avoid concision, disconnect all RGB inputs before entering the Installer
menu.
Overview: Commercia[ Mode Setup Procedure
1.Set Instaiter
Menu Items
(Enter Installer Menu, see page 43 for detailed instructions.)
a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER.
(This clears aU installer menu items, custom settings, channel labels/icons
and reloads the factory default settings.)
b.Set Item 003 BAND/AFC.
Broadcast: set to O00.
- HRC: set to 002
- CATV: set to 001.
- [RC: set to 003
c. Set item 028 CH OVERIDE to 001. This allows access to Auto Program,
Channel Labels and Channel List options in the Channel Menu.
d. Set other particular installer items that affect your TV programming
network. See pages 46 - bl.
e. After all required installer menu item settings have been adjusted, press
ENTERon the remote to remove Installer Menu.
[lIlII]
I I_[."I I*.l I ! :I II,.'i
:[_|
bIlII]
in,l
[i[i)'!
[*I*Ic]
I:T_q_llJl_1:[e,]
[i[i)I4
[o?fi:]
[e_:P[olU _ :lID] =
[oIo]l
[I]r#]
[lII] I
2. Set Up 11/ Features
(See Picture, Sound, Setup menus etc. See TV CLonab[e options list on page
52.) InstaUer Note: Some TV features will have to be set up after running
Auto Program. An example is Digital Font options. This feature is not
available until digital channels are found in the channel scan. Set up
Digital Font options after Auto Program finds a digital channel with
digital captions. Do this before running 2-5-5 + Menu.
3. Run Auto Program
(Search for all available channels.) Go to the Channel menu and access the
Auto Program option, follow on-screen instructions.
a. Edit Channel Scan. In the Channel Menu, access the Channel List menu.
• Delete channels per your system requirements: do you want to delete any
free channels so the guest cannot access them?
• Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel on-
screen display. Add identifiable Labels for the end user to readily know what
common networks are available. In the Channel menu, select the Channel
Label option, follow instructions on the bottom of the screen.
[d_;[;!
l_ll
[elvd=;llD]:
[lIIII]
4. Transfer TV Setup to Controller Box: 215-5 -i- Menu
After the TV channel scan has been edited and channel Label icons added,
enLer the Installer menu. Once in the Installer
menu, press 2-5-5 and MENU
on the remote. This transfers the TV setup to the internal controller box.
*Note: Only do 2-5-5 +/4ENU once or TVsetup may be corrupted.
TVscans available channels and exits menu when transfer to controller is
complete.
5. Perform Adding Custom Channel Labets: 2-5-4 + Menu Mode
Enter Installer menu, press 2-5-4 and Menu. Add your own custom [abels to
the channel on-screen displays. (See page 53.) To remove menu press MENU.
*Note: 2-5-4 + MENU can be performed more than once.
Verify 11/Setup
At this point, verify that the channel Lineup, channel icons and custom [abels
are correct. Make sure the TV features are set per your requirements.
Set item 028 CH OVERIBE to O00 to Loci<the channel scan. After the
preceding has been completed, the Master TV setup is ready to be copied to
the LT2002 CLone Programmer, see next page.
PAG E 42
L26W58HA InstaLLer Menu
L26W58HA Instalter Menu Items
DIGITAL
1g-3
ANALOG
2
_
[_
WXYZ
WXYZ
MONO
Custom Channel Label 'WXYZ' created in
2-5-4 + Menu Add Channel Label Mode
After TV setup has been verified,
set item 028 Ch Overide back to 000.
*Note: Default setting for Aux sources is to be active in the
installer menu. The Aux sources will appear between the high-
est Ana!og and lowest Digital channel number with Channel
Up/Down. If the Aux sources wil! not be used, it is advisable
to set them to 000 (Off) before doing 2-5-5 + Henu. A_et
doing 2 5 5 + Menu, the only way to turn the Aux source off
so they wil! not appear in the channel scan, is to go to the
Channel Bank menus and turn eacb Aux source of.f by selecting
"Normal Delete_
Refer to installer items: 34, 35, 38, 39, 87, 92, and 92.
Advertisement
