Model W1793/W1794 Professional Spray Gun SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
Page 4
Model W1793/W1794 Professional Spray Gun Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18.
Model W1793/W1794 Professional Spray Gun Additional Safety Instructions for Spray Guns READ THIS MANUAL. This manual PROTECTIVE CLOTHING. Protect contains proper operating exposed skin from overspray by instructions for this spray gun. wearing a protective suit or other approved garment. READ MATERIAL LABELS and MATERIAL SAFETY DATA SHEETS INAPPROPRIATE USE.
Material Capacity ..600 ml / 20 fl oz control program assure safe and reliable Pattern Width ....180–280 mm operation. Woodstock International, Inc. is commit- W1794 Specifications ted to customer satisfaction. Our intent with this manual is to include the basic Type .......
Page 7
Model W1793/W1794 Professional Spray Gun SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1793/ W1794.
Page 8
Model W1793/W1794 Professional Spray Gun Assembly Controls Insert the filter into the gun body Atomizing Cap (see Figure 6). Fluid Control Trigger Pattern Control Air Flow Control W1794 Regulator Figure 7. Controls. Fluid Control: Controls the volume Figure 6. Installing filter. of material that travels through the fluid tip.
Page 9
Model W1793/W1794 Professional Spray Gun OPERATIONS Spraying The Model W1793/W1794 spray gun is designed to spray low to medium viscosity liquids, like lacquers, stains, primers, multi-component paints, acrylics, epoxies etc. It is ideal for auto body touch-ups, woodworking projects, or projects with hard to reach areas. EXPLOSION HAZARD! DO NOT smoke or have any source of flame or spark To use your spray gun:...
Page 10
Model W1793/W1794 Professional Spray Gun 7. Adjust the fluid control knob to 10. Begin spraying 2-3 inches before start with a low volume of material the work piece and continue to the and keep the atomization as low end of the work piece. Continue the as possible.
Model W1793/W1794 Professional Spray Gun Atomizing Cap and Fan Rotating the pattern adjustment control in Figure 11 will give you a range Adjustments between the two patterns in Figure 12. The atomizing cap needs to be adjusted for horizontal or vertical spraying Pattern patterns.
Model W1793/W1794 Professional Spray Gun CLEANING & LUBRICATION Cleaning 5. Unscrew the atomizing cap with your fingers and the fluid tip with Proper cleaning is the best way to ensure the service wrench. The fully trouble free performance from your disassembled gun should look like Figure 13.
Page 13
Model W1793/W1794 Professional Spray Gun Lubrication Lubricate the following areas with spray gun lube after cleaning: A. Atomizing Cap Threads B. Air Valve Packing C. Trigger Pin D. Air Flow Control Valve E. Pattern Control F. Fluid Control Knob After each cleaning, apply a thin film Figure 14.
Model W1793/W1794 Professional Spray Gun Troubleshooting Symptom Possible Cause Possible Solution Fluttering or 1. Dry or worn fluid tip seat 1. Tighten fluid tip or replace Spitting spray. permits air to seep into fluid seat with new one. passage. 2. Material level too low. 2.
Page 15
Model W1793/W1794 Professional Spray Gun Symptom Possible Cause Possible Solution Excessive over- 1. Fluid pressure too high. 1. Reduce fluid pressure. spray. 2. Gun is too far from surface. 2. Keep gun at recommended distance. 3. Spraying too fast. 3. Slow down and maintain consistent, even parallel stroke.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox machine or machine part which in normal use has proven to be defective,...
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
Page 20
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
Need help?
Do you have a question about the SHOP FOX W1793 and is the answer not in the manual?
Questions and answers