Care And Cleaning - Panasonic Viera TC-L37X2 Operating Instructions Manual

Technical Information (Continued)
I-" I _I_
@Aspect Ratio:
Size 1
@Aspect Ratio:
4:3
€ii Size 2
FULL/JUST(HIFILL!ZOOM)
See page 28 for more information
@ The width will be decreased on both sides to
reduce noise.
@ The width will be increased on both sides to
reduce noise.
* Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC
525 (480) / 60i 15.73 59.94 *
525 (480)/60p ' 31.47 " 59.94 ' * ' * '
750 (720)/60p 45.00 59.94 * *
1,125 (1,080) 160i ' 33.75 " 59.94 ' * ' * '
1,125 (1,080)/60p 67.43 59.94 *
1,125 (1,080)/60p ' 67.50 " 60.00 ' ' * '
1,125(1,080)/24p 26.97 23.98 *
1,125(1,080)/24p ' 27.00 " 24.00 ' ' * '
640 x 400 @70 31.47 70.08 *
640 x 480 @60 ' 31.47 " 59.94 ' ' ' *
Macintosh13" (640 x 480) 35.00 66.67 *
640 x 480 (_,,75 37.50 " 75.00 ' ' ' *
852 x 480 @60 31.44 59.89 *
800 x 600 @60 ' 37.88 ' 60.32 ' ' ' *
800 x 600 @75 46.88 75.00 *
800 x 600 (_,,85 53.67 " 85.08 ' ' ' *
Macintosh16" (832 x 624) 49.73 74.55 *
1,024 × 768 @60 ' 48.36 ' 60.00 ' ' ' *
1,024 x 768 @70 56.48 70.07 *
1,024 × 768 @75 ' 60.02 ' 75.03 ' ' ' *
1,024 x 768 @85 68.68 85.00 *
Macintosh 21" (1,152 x 870) 68.68 75.06 *
1,280 x 768 @60 47.78 59.87 *
1,280 x 1,024 @60 ' 63.98 ' 60.02 ' ' ' *
1,366 x 768 @60 48.39 60.04 *
I.]tL"t11_r;'_'i_ I
@ Signals other than above may not be displayed properly.
@ The above signals are reformatted for optimal viewing on your display.
@ Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
@ Some PC models cannot be connected to the set.
@ There is no need to use an adapter for computers with IBM PC/AT compatible D-sub 15P terminal.
@ The maximum resolution: 1,280 x 1,024
If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.
@ Signal Names for D-sub 15P Connector
Pin Layout for PC Input Terminal
signal Name Signal Name Signal Name
(1) R LfL6) GND (Ground) 1_ NO (not connected)
G (7) GaD (Ground) @ NC
_3_ B (8_ GaD (Ground) @ HD/SYNC
@ NC (not connected) @ NC (not connected) _ VD
@ GND (Ground) GND (Ground) NC
Care and Cleaning
First, unplug the Power cord plug from the wall outlet.
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft,
lintfree cloth.
@ If the surface is particularly dirty, soak a soft, lint-free cloth in diluted mild liquid dish soap (1 part mild liquid dish soap diluted
by 100 times the amount of water) and then wring the cloth to remove excess liquid. Use this cloth to wipe the surface of the
display panel, then wipe it evenly with a dry cloth of the same type until the surface is dry.
@ Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid contact with volatile
substances such as insect sprays, solvents, and thinner; otherwise, the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
@ If the cabinet is particularly dirty, soak the cloth in a weak mild liquid dish soap and then wring the cloth dry. Use this cloth to
wipe the cabinet and then wipe it dry with a dry cloth.
@ Do not allow any mild liquid dish soap to come into direct contact with the surface of the LCD TV.
If water droplets get inside the unit, operating problems may result.
@ Avoid contact with volatile substances such as insect sprays, solvents, and thinner; otherwise, the quality of the cabinet
surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with
articles made from rubber or PVC.
@ Cleaning
Wipe the surfaces with a soft, dry cloth. If the unit is particularly dirty, clean it using a cloth soaked with water to which a small
amount of mild liquid dish soap has been added and then wipe with a dry cloth.
Do not use products such as solvents, thinner, or household wax for cleaning, as they can damage the surface coating.
(If using a chemically-treated cloth, follow the instructions supplied with the cloth.)
@ Do not attach sticky tape or labels, as they can make the surface of the pedestal dirty. Do not allow long-term contact with
rubber, vinyl products, or the like. (Doing so will cause deterioration.)
Wipe the plug with a dry cloth at regular intervals. (Moisture and dust can lead to fire or electrical shock.)
@
oO
R:::3
7_0
o
'_£c}
48 49