Vision Fitness T970HRT Service Manual
  1. Manuals
  2. Brands
  3. Vision Fitness Manuals
  4. Treadmill
  5. T970HRT Service
  6. Service manual
Vision Fitness T970HRT Service Manual

Vision Fitness T970HRT Service Manual

Vision series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Vision Fitness T970HRT

Summary of Contents for Vision Fitness T970HRT

  • Page 2: Table Of Contents

    TABLE OF CONTENTS SECTION 1: MAINTENANCE PROCEDURE MAINTENANCE CHECK LIST TENSIONING THE BELT PROCEDURE DECK RE-WAXING PROCEDURE CLEAN THE GROOVES PROCEDURE LUBRICATING THE AIR SHOCK PROCEDURE SECTION 2: WIRING DIAGRAM T9700 MCB NAME : MEB1J (WIRING DIAGRAM) T9600/T9500 MCB NAME : MEA9J (WIRING DIAGRAM) T9450/T9350/T9300/T9200/T9250 MCB NAME : JHT2.0(WIRING DIAGRAM) SECTION 3: CONSOLE ENGINEERING MODE GUIDE...

  • Page 3: Section 1: Maintenance Procedure

    SECTION 1 MAINTENANCE PROCEDURE...

  • Page 4: Preventive Maintenance Schedule

    PREVENTIVE MAINTENANCE SCHEDULE VISION TREADMILL Item Daily Weekly Monthly Quarterly Biannual Annual Console Mounting Inspect Bolts Frame Clean Inspect Clean Running Belt Top Inspect (Vacuum) #3 Carbon Brush Inspect Replace Power Cord Inspect Display Console Clean Inspect Handlebar Clean Inspect Handrail &...

  • Page 5: Tensioning The Belt Procedure

    TENSIONING THE BELT Caution: Over-tightening of the roller will severely shorten the life of the belt and may cause further damage to other components. Running Belt: If when you plant your foot on the belt, you can feel a slipping sensation then the belt has stretched and is slipping across the...

  • Page 6: Deck Re-Waxing Procedure

    DECK RE-WAXING PROCEDURE Frequency: Every 1 month. LUBE Name: DOW CORNING 350 SILICON Procedure: 1. Loosen the tension bolts at both ends. 2. Pull the belt with your left hand and apply the silicon in the deck with your right hand. (The volume of silicon applied is about 25CC.) 3.

  • Page 7: Clean The Grooves Procedure

    CLEAN THE GROOVES PROCEDURE Frequency: Every 3 months. Procedure: 1.Remove the drive belt and check the grooves in belt for dirt or dust and clean it. 2.Check the grooves in motor pulley for dirt or dust and clean it. 3Check the grooves in roller pulley for dirt or dust and clean it.

  • Page 8: Lubricating The Air Shock Procedure

    LUBRICATING THE AIR SHOCK Frequency: Every 6 months. Procedure: 1. Fold up the frame by using the deck-locking lever. 2. Add the lubricating oil on the shaft of the air shock. 3. Lift the frame up and down, repeating this several times to allow the lubricating oil blend into air shock.
  • Page 9 SECTION 2 WIRING DIAGRAM INSTRUCTION...
  • Page 10 T9700(TM51D/E) MCB WIRING(FOR 110V / 220V) T1-----Motor wire (black) T2-----Motor wire (red) T3-----D1 of on/off switch T4-----D3 of on/off switch T5-----20-pin console cable T6-----Elevation cable T7-----Speed sensor line T8----- Ground wire...
  • Page 11 T9600HRT(COMFORT)/T9600HRT/T9500HRT/T9450HRT/T935 0/T9300 MCB WIRING(FOR 110V / 220V) T1-----Motor wire (black) T2-----Motor wire (red) T3-----D1 of on/off switch T4-----D3 of on/off switch T5-----8-pin console cable T6-----Elevation cable T7-----6-pin console cable T8----- Speed sensor line T9----- Ground wire...
  • Page 12 T9200/T9250 MCB WIRING(FOR 110V / 220V) T1-----Motor wire (black) T2-----Motor wire (red) T3-----D1 of on/off switch T4-----D3 of on/off switch T5-----8-pin console cable T6-----Elevation cable T7-----6-pin console cable T8----- Speed sensor line T9----- Ground wire...

  • Page 13: Section 3: Console Engineering Mode Guide

    SECTION 3 CONSOLE ENGINEERING MODE GUIDE...

  • Page 14: How To Enter Into The Engineering Mode

    T9700(TM51D/E) TREADMILLS (for Software Ver. 2.5) Apply to : 1. VISION T9700/T9600 serise treadmail . 2. 2004 year T9700 serise treadmail. 3. 2004 year for ID How to enter into the engineering mode? 1. Press & Hold both “ELEVATION UP” and “SPEED DOWN”...
  • Page 15 KEY BEHALE FUNCTION key name function SELECT To Store up the parameter SPEED UP Add this show parameter of speed and elevation Decrease this show parameter of speed and SPEED DOWN elevation STOP Press the STOP key for 3~5 sec will reset to sources ELEVATION UP Add address ELEVATION DOWN...
  • Page 16 P13 ELV DIR Change the incline altitude P14 ELV ERRS Change the altitude error switch, 0=OFF, 1=ON P15 SCROLL set the change display show letter speed P16 LUBE HRS Accumulate the after one lube to now hour 0xffff P17 CLEAN Accumulate the after clean to now distance 0xffff P18 BRUSH...
  • Page 17 T9600HRT(COMFORT)/T9600HRT/T9500HRT/T9450HRT/ T9350/T9300 TREADMILLS ( for Software Ver. 5.9) Apply to : 1. VISION T9300/T9350/T9400/T9450/T9500 serise treadmail. 2. 2004 year T9300/T9350/T9450/T9500/T9600 serise treadmail. 3. 2004 year T9350/T9450/T9500 for ID How to enter into the engineering mode? 1. Press & Hold both “ELEVATION UP” and“SPEED DOWN”...
  • Page 18 KEY BEHALE FUNCTION key name function SELECT To Store up the parameter SPEED UP Add this show parameter of speed and elevation SPEED DOWN Decrease this show parameter of speed and elevation ELEVATION UP Add address ELEVATION DOWN Decrease address START Enter P0~P14 parameter ENG1...
  • Page 19 Appendix (1) SOU=SOURCES PARAMETER SCO=SCOPE PARAMETER MODEL Metric/ English SET SOU SCO SOU SCO SOU English 2~70 363 T9300 250~511 100~270 1~150 130~255 (TM55) Metric 2~70 363 250~511 100~270 1~150 130~255 T9300HRT English 2~70 363 250~511 100~270 1~150 130~255 (TM55D) Metric 2~70 363 250~511...
  • Page 20 Metric 2~70 250~511 100~270 1~150 130~255 English 2~70 250~511 100~270 1~150 130~255 Metric 2~70 250~511 100~270 130~255 1~150 T9600HRT English 2~70 250~511 100~270 1~150 130~255 (TM53) Metric 2~70 250~511 100~270 1~150 130~255 Appendix (2) Metric/ Configuration Min. Max. Speed Model English Number Speed...
  • Page 21 Remarks : 1. If set address P6 model is T9450(Configuration Number 6/7/23/33) machine the address P11 will automatic set to 7,because running band the depth is 4.4mm. 2. If you want to the clean accumulate time and distance, please press the "ELEVATION UP and DOWN"...
  • Page 22 T9200/T9250 TREADMILLS ( for Software Ver. S706) How to enter into the engineering mode? 1. Press & Hold both “ELEVATION UP” and “SPEED DOWN” at the same time for3-5 sec. Then, the dot vision display first will show VERSION ” follow show ENG 1 ”...
  • Page 23 ENG1 ADDRESS DEFINITION SOURCES SCOPE MIN SPD 210~3900 MAX SPD 2000 2000~3900 No function No function ELV ZERO 1~255 ELV MAX 1~255 No function MAX TIME 5~99 min(Km/Mile the same) WEIGHT 150LB(Mile) 35~400LB(Mile) 68kg (Km) 35~400kg(Km) OP HOURS (hr) 0~9999 OP DIST 0~9999 (Mile/km)

  • Page 24: Section 4: Mcb Led Instructions

    SECTION 4 MCB LED INSTRUCTIONS...

  • Page 25: Mcb Led Indication

    MCB LED Indication When we designed the lower control board (MCB) for our treadmills we placed status lights (LEDs) on it to aid in field Note: diagnosis and repair. The following is an overview of what Use a multi-meter these indicator lights mean and what can be checked with to test the power them in the field.
  • Page 26 MCB LED Indication Light- When lit, indicates the High Power Direct Current supply for the motor (B+) is online. This light will remain lit for a period of time after power has been removed from the MCB. While the MTR light remains lit, anyone handling the MCB should use caution since there is still a hazardous potential present.
  • Page 27 MCB LED Indication Light- Indicates the PCB is commanding the incline motor to move up. If the User is Note: commanding the incline to increase and this light is not lit, the incline is being check cabling, verify proper PCB operation and replace it commanded up if either is defective.

  • Page 28: Pwm Mcb Led Chart

    PWM MCB LED CHART NO. AC +18V +11V MTR I-LIMIT OFF OFF OFF OFF OFF OR BLINKING DIM/ BLINKING BLINKING COMES ON BRIEFLY & THEN SHUTS...

  • Page 29: Mcb Led Troubleshooting Chart

    MCB LED-AIDED TROUBLESHOOTING CHART PROBLEM/RESULT CORRECTIVE ACTION Verify connections, power switch, circuit No operation of MCB or PCB breaker and fuse No operation of MCB or PCB Check fuse F1 PCB will not power up Replace MCB Verify adequate line voltage. If line voltage is PCB will power up but the MCB adequate, MCB is damaged and needs to be will not operate...
  • Page 30 SECTION 5 TROUBLESHOOTINGS...

  • Page 31: No Display On Console

    No display on console Possible causes: 1. Breaker is damaged. 2. ON/OFF switch is damaged. 3. MCB is damaged. 4. 6-pin console cable is damaged. 5. PCB is damaged. Fix: 1. ( refer to “MCB LED layout & indication”……SECTION 6) Verify if LED 115vAC(AC) is lit.

  • Page 32: Running Speed Is Not Stable

    Running speed is not stable Possible causes: 1. AC power voltage is too low. 2. Tension of drive belt or running belt is too loose. 3. Poor adjustment of MCB. 4. MCB is damaged. 5. Motor is damaged. Fix: 1. Check the power voltage by using voltage-meter to see if it is within 120V D 15% or 230V D 15%.

  • Page 33: Treadmill Starts To Run By Itself

    Treadmill starts to run by itself Possible causes: 1. The console cable is broken. 2. PCB is out of order. 3. MCB is out of order. Fix: 1. Replace the console cable with a new one. 2. Replace the PCB. 3.

  • Page 34: Noise Generated Under Motor Cover

    Noises generated under motor cover Possible causes: 1. The running belt tension is adjusted too tight. 2. The bearing of front roller is not installed correctly. 3. Dirty grooves of drive belt. 4. The motor is damaged. Fix: 1. Adjust the belt tension so that the belt does not start slipping and then check if the noise has...

  • Page 35: Treadmill Will Not Start

    Treadmill will not start Possible causes: 1. MCB is damaged. 2. 8-pin console cable is damaged. 3. PCB is damaged. 4. Motor is damaged. Fix: Open motor cover, verify wire connection MTR1 and MTR2 on the MCB then plug in the power cord and turn on the power switch. Then press “START“...

  • Page 36: Incline Function Does Not Work

    Incline function does not work Possible causes: 1. The 8-pin console cable is damaged. 2. Incline motor is damaged. 3. PCB is damaged. 4. MCB is damaged. 5. The incline setting is not correct. Fix: Enter to the Engineering Mode to recalibrate the elevation values Then press "FAST"...

  • Page 37: Heart-Rate-Control Function Does Not Work

    Heart-Rate-Control function does not work Possible causes: 1. Transmitter does not contact with user's chest very well. 2. Transmitter(Polar-belt) is at low battery status. 3. Transmitter(Polar-belt) is damaged. 4. Heart-rate-control board is damaged. 5. PCB is damaged. Fix: 1. Center the transmitter on your chest below the pectoral muscle(breast) as shown, then check again.

  • Page 38: Error Messages On The Console

    Error Messages on the Console T9700 (TM51D/E) Error code definition Error Definition Incline motor parameter over the set Incline motor not to movement Incline motor the signal not answer Speed over the 2.0 mph 0 km/h Error Message "E4" : Please enter the engineer mode to execute the AUTO-CAL MODE.
  • Page 39 T9600HRT (COMFORT)/T9600HRT/T9500HRT/T9450HRT/T9350/T9300 Error code definition Error Definition Incline motor parameter over the set Incline motor not to movement Incline motor the signal not answer TROUBLESHOOTINGS Error Message " E4" : Please enter the engineer mode to execute the AUTO-CAL MODE Error Message "...
  • Page 40 T9200/T9250 Error code definition Error code definition Error Definition Incline motor problem Error Message " E2" : 1. Please check the incline motor cable whether to inset MCB. 2. Check the console signal whether transmission to MCB, you can refer to MCB LED UP and DOWN.

  • Page 41: Section 6 : Software Upgrade Procedure

    SECTION 6 SOFTWARE UPGRADE PROCEDURE Revision: 1.0 Date: 1999-09-01...

  • Page 42: Vision Series Treadmill Software Upgrade Sop

    VISION SERIES TREADMILL SOFTWARE UPGRADE SOP Service Tools & Accessories: Computer (Notebook is preferred) Connection cables ( Parts NO: MQMXCV001 and MQMXCV002) Software Revision: 1.0 Date: 1999-09-01...
  • Page 43 B. Steps: 2. Connection cables & short pin is ready. 3. Turn ON the power switch. 4. Find out the software version file in the computer and then actuate/open the file by “click” the mouse twice. 5. The computer will be turned into DOS mode, and run the installation work. Automatically. (It takes around 2 minutes for installation.) 6.

This manual is also suitable for:

T9700runerT9700sT9600hrtT9500hrtT96450hrtT9350 ... Show all

Table of Contents