Oil And Fuel Information; Fueling Unit - Troy-Bilt TB26TB Operator's Manual

WARNING:
OVERFILLING OIL CRANKCASE MAY
CAUSE SERIOUS PERSONAL INJURY. Check and
maintain the proper oil level in the crank case; it is
important and cannot be overemphasized. Check the
oil before each use and change it as needed. See
Changing the Oil (p. 9).
RECOMMENDED OIL TYPE
Using the proper type and weight of oil in the crankcase is
extremely important. Check the oil before each use and
change the oil regularly. Failure to use the correct oil, or using
dirty oil, can cause premature engine wear and failure.
Use a high-quality SAE 30 weight oil of API (American
Petroleum Institute) service class SF, SG, SH.
ADDING OIL TO CRANKCASE: INITIAL USE
NOTE: This unit is shipped empty of oil. In order to avoid
damage to the unit, put oil in the crankcase before you
attempt to start the unit.
Your unit is supplied with one 3.04
fluid oz. (90 ml.) bottle of SAE 30
SF, SG, SH oil (Fig. 4).
NOTE: Save the bottle of oil. It
can be used to measure the
correct amount during future
oil changes. See Changing
the Oil (p. 9).
1. Unscrew the top of the bottle of oil and remove the paper
seal covering the
opening. Replace the
top. Next, cut the tip off
the funnel spout (Fig. 4).
2. Place the unit on a flat
level surface (Fig. 5).
3. Remove the dipstick
from the crankcase (Fig.
6).
4. Pour the entire bottle
of oil into the oil fill
hole (Fig. 6).
NOTE: Never add oil to
the fuel or fuel tank.
5. Wipe up any oil that
may have spilled and
reinstall the oil fill plug/
dipstick.
Check oil before each use and change as needed. Refer to
Checking the Oil Level (p. 9).
RECOMMENDED FUEL TYPE
Old fuel is the primary reason for improper unit performance.
Be sure to use fresh, clean, unleaded gasoline.
NOTE: This is a four cycle engine. In order to avoid damage to
the unit, do not mix oil with gasoline.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates
such as ethanol, methanol or MTBE (ether). Alcohol-blended
fuel absorbs water. As little as 1% water in the fuel can make
fuel and oil separate or form acids when stored. Use fresh fuel
(less than 60 days old), when using alcohol-blended fuel.
Using Blended Fuels
If you choose to use a blended fuel, or its use is unavoidable,
follow recommended precautions:

OIL AND FUEL INFORMATION

Funnel
Spout
Fig. 4
Oil Fill
Fig. 5
O-Ring
Oil Fill Plug/
Dipstick
Oil Fill Hole
Fig. 6
• Always use fresh unleaded gasoline
• Use the fuel additive STA-BIL
• Drain tank and run the engine dry before storing unit
Using Fuel Additives
The use of fuel additives, such as STA-BIL
an equivalent, will inhibit corrosion and minimize the formation
of gum deposits. Using a fuel additive can keep fuel from
forming harmful deposits in the carburetor for up to six (6)
months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel
according to the instructions on the container. NEVER add fuel
additives directly to the unit's gas tank.
WARNING:
outdoor area. Wipe up any spilled fuel immediately.
Avoid creating a source of ignition for spilt fuel. Do
not start the engine until fuel vapors dissipate.
WARNING:
Ignited vapors may explode. Always stop the engine
and allow it to cool before filling the fuel tank. Do not
smoke while filling the tank. Keep sparks and open
flames at a distance from the area.
FUELING THE UNIT
WARNING:
from fuel spray. Never operate the unit without the
fuel cap securely in place.
1. Remove the fuel cap (Fig. 7).
2. Place the gas
container's spout into
the fill hole on the fuel
tank (Fig. 7) and fill the
tank.
NOTE: Do not overfill the
tank.
3. Wipe up any gasoline
that may have spilled.
4. Reinstall the fuel cap.
5. Move the unit at least
30 ft. (9.1 m) from the
fueling source and site before starting the engine.
NOTE: Dispose of the old gasoline in accordance to Federal,
State and Local regulations.
5
®
or an equivalent
®
Gas Stabilizer or
Add fuel in a clean, well ventilated
Gasoline is extremely flammable.
Remove fuel cap slowly to avoid injury
Gas Can
Spout
Fuel Tank
Fuel Cap
Fig. 7