Advertisement
Quick Links
Download this manual
See also:
User Manual
IMPORTANT
If your printer is new, set it up according to
the enclosed manufacturers instructions.
This is a check to ensure your new printer
and drivers are working correctly before the
Eco-Flo System is installed.
It is very important you read these instructions carefully before you begin!
We will take you through the following steps:
1
Preparing your Injector
2
Setting up of the Inks in the bottle tray
3
Installation of the modified injector to your printer
4
Fitting of the Tube Supports System
5
Producing your first print.
Only start work on the installation once you have read the
What you will need to Install the Eco-Flo 2100
•
Complete Eco-Flo 2100 Kit
•
Sharp Blade (Stanley Knife type) & Scissors
•
Measuring Tape or Ruler
•
Marking Pen or Pencil
•
Paper Towels
Please read carefully before you continue and
refer to the components diagram over the
page.
Check List for components
Assembly Instructions for
EPSON PRINTER
instructions fully!
Set of 7
125ml Inks
ECO-FLO CONTINUOUS INK SYSTEM
2100 Ink System
:
What is included in your Eco-Flo 2100 Kit
•
Injector Set with tubes attached
•
Set of 7 Inks & empty 100ml bottles
•
Black Tube Support Bracket with Hook &
Loop Fastener fitted
•
Bottle Holder Tray
•
Special Chip Block
•
1 Grey/White Tube Clip with adhesive pad
•
Installation Instructions and Profiles CD
•
10ml Syringe & wing adaptor
•
Pair of latex gloves
•
Special Foam Block
•
7 Tube Clamps
•
7 Bottle Caps & Clear Piping Tubes
1
Wing Adaptor
Perma
Jet
Epson 2100
Part No. A26421
Epson 2100 Eco-Flo Shown
Black Tube
Support Bracket
.
Advertisement
Related Manuals for Epson 2100
Summary of Contents for Epson 2100
-
Page 1: Ink System
Installation of the modified injector to your printer Fitting of the Tube Supports System Producing your first print. Only start work on the installation once you have read the What you will need to Install the Eco-Flo 2100 • Complete Eco-Flo 2100 Kit •... - Page 2 Injector Set & Tubes 7 Empty 100ml Bottles Bottle Caps & Clear Piping 10ml Syringe ____________________________________________________________________________________________ Check Printer Condition 7 Tube Clamps Pair of Latex Gloves Bottle Holder Tray Special Chip Block (Wrapped in Protective Packaging) Special Foam Block that may...
- Page 3 If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson injectors that came with the printer. Follow normal installation instructions for the software. Test the printer by printing pictures. Learn how to use the Epson utilities to run a Nozzle pattern check and to run a Cleaning Cycle.
- Page 4 Fig.2 Step 3 Bottle Preparation Locate the coloured bottle caps and straight lengths of plastic tubes. Insert the straight tube firmly into the bottom of each bottle cap see Fig.3 Fig.3 Step 4 Tube Preparation...
- Page 5 Fig.4 Fig.5 Step 5 Preparation of The Clamps & Inks Fig.7 Step 6 Positioning the ink Bottles in the Tray You are now ready to position the ink bottles in the bottle holder tray as indicated below. Using a pair of scissors separate all tubes by snipping gently at the tube ends.
- Page 6 Step 8 Priming the Ink Through the Injectors You are now ready to start the ink priming process starting with the YELLOW injector. 2100 Setup When you have completed the above process insert the correct tube to the correct ink bottles. PLEASE TAKE...
- Page 7 Please place the Chip block as indicated in Fig.14 below making sure that this is correctly positioned & installed. Once you have installed this you are ready to insert the set of 7 injectors in the printer carriage. Priming an...
- Page 8 The tubes can be inserted at this time through the available opening in the bracket – the tubing goes under the bracket, then up and then through. It is advisable to slide the tubes as far forward to the front of the printer...
- Page 9 Next, you will notice that the Tube Support Bracket has both the Hook and Loop Velcro on it. The Hook portion of the Velcro is going to end up attached to your printer. The Loop portion will remain on the Tube Support Bracket. Do not separate the Hook and Loop.
- Page 10 This can be done manually by moving the head to the left and right and checking that there is just enough tubing to allow the print head to move freely, without it dragging against any part of the printer see Fig. 20 &...
- Page 11 The printer should come on and the head should move back and forth a few times and do a cleaning cycle. When it stops moving, only the green light should be on. A red light at this point indicates that one of the chips has not been recognized. If this is the case please LOCK all tubes with the white clamps and very carefully remove the Injectors, Foam Block and Special Chip Block, Now very carefully check the chip that is not registering.
- Page 12 ECO-FLO INSTALLATION INSTRUCTIONS FOR ALL TYPES OF PRINTERS AND SYSTEMS TROUBLE SHOOTING GUIDE INK PURGE TEST FILES AND TONE CHARTS ICC PROFILES FOR USE WITH PERMAJET COLOUR INK AND PAPER COMBINATIONS CURVES FOR USE WITH MONOCHROMEPRO INK SYSTEM. IN ORDER TO USE THE PERMAJET INK SYSTEM TO ITS FULL POTENTIAL, YOU SHOULD NOW TAKE THE TIME TO OPEN THE ENCLOSED CD AND PROCEED TO READ THE FULL “HOW TO INSTALL AND USE ICC PROFILES”...
- Page 13 • It is advisable not to let your printer sit for long periods of time without printing something. The use of a timer to power up the printer should you be going away for a long period of time is recommended.