12 or 16 gallon full blowing wet/dry vac (9 pages)
Summary of Contents for Craftsman 113.177060
Save This Manual for Future Reference SEARS owner's manual MODEL 113.177060 I:RRFTSMRN Serial ',lumber Model and serial 16 GALLON numbers may be found on the side of the WET/DRY VAC powerhead, You should record both WITH DETACHABLE model and serial numbers in a safe place for future use.
ON CRAFTSMAN WET/DRY VACS If within one year from the date of purchase, this Craftsman Wet/Dry Vac tails due to a defect in material or workmanship, Sears will repair it, free of charge. If this Craftsman Wet/Dry Vac is used for commercial or rental purposes, this warranty coverage applies for only 90 days from date of purchase.
Toavoid injury f rom accidental starting, Vacs before servicing. unplug p ower cordbefore c hanging or Use this Wet/dry Detachable Blower Vac cleaning filter. as described in this manual. Donotunplug b ypulling o ncord. To When using as detached blower: unplug, grasp t heplug, n ot t hecord.
Introduction Table of Contents This Wet/Dry Vac is intended for house- hold use only. item Page IMPORTANT NOTE Warranty Information ......Safety Instructions ......... Please Read Carefully Introduction..........Static Shocks Are Common - In dry Unpacking and Checking areas or when the relativehumidityof the Carton Contents ......
Float/Cage Assembly Detachable WARNING: For your own safety, never connect plug to power source outlet until all assembly steps are complete and you have read and understood the safety and operation instructions. Do not operate vac with any parts damaged or missing. 1.
Filter Assembly 1. Carefully slide the filter over the tilter cage, sliding it over the center ring cov- ering the 3 slots until the tilter stops against the lid. 2. Place the hole in the filter plate over threaded screw of the fgter cage. Filter 3, Gently push on the filter plate to seat the rubber ring of the filter inside the cir-...
4.Position thedovetail portion o fone of 5.Turn theaccessory caddy u pright. thewheel assemblies into theacces- This completes theassembly ofyour16 sory caddy a sillustrated. Tap the wheel gallon w eVdry vacaccessory caddy. support into theaccessory caddy w ith a The caddy i snow ready t oinstall thesix- soft m allet.
To Store Your Accessories 1. Your Sears Craftsman wet/dry vac is designed to provide better stability, mobility and accessory storage with the addition of the caddy. Located at the rear of the caddy are five storage pock- ets. Wet/dry vac accessories may be conveniently stored here while not in use.
Positioning Detachable Blower (Power Head Assembly) 1, Locate the Detachable blower o! your Sears Craftsman vac. The top of the detachable blower has two hinges. To assemble the detachable blower to the lid assembly, the two hinges need to Hinge...
Operation WARNING To avoid fire or explosion, do not operate this vac in areas with flammable gases or flammable vapors such as lighter fluid, cleaners, oil*base paints, gasoline, alcohol or explosive dust such as coal, magnesium, grain or gun powder in the air. Do not vacuum explosive dust, flammable or combustible liquids or hot ashes.
Emptying Dust Drum Drum Latch WARNING: To avoid injury from accidental starting, unplug power cord before emptying the drum. I. To remove the lid to empty contents of the dust drum, simply liftthe drum latch holding the lid to the drum/caddy assembly and lift the lid assembly up and off the drum.
Operation (continued) Blowing Feature WARNING: Always wear safety gog- Your wet/dry vac features a "detachable gles complying with ANSI Z87.1 blower". It has the capability to be used as when us ng as a blower. a dedicated blower for yard work, patio cleanup and workshop applications to blow sawdust and other debris.
IMPORTANT: To avoid damage to the To clean the foam pad under the intake blower wheel and motor, always reinstall shield of the detachable blower: the filter before using the va¢ for dry t. Remove the three screws holding the matedat pickup, intake shield.
farthest from you,) Wet Nozzle To pick up liquids off a smooth surface, use the 2-1/2" wet nozzle accessory sup- 2. Using both hands, lower the nozzle plied with your wet/dry vac. To use this nozzle, simply attach the nozzle to the body onto the insert and squeegee with the round opening of the nozzle closest end of an extension wand.
Repair Parts 16 Gallon Wet/Dry Vac With Detachable Blower Model Number 113.177060 Always order by Part Number - Not by Key Number WARNING SERVICING OF DOUBLE-INSULATED WET/DRY In a double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added.
£RRFTSMRN® Accessories and Attachments Get more versatility from your Craftsman wet/dry vacuum by adding these accesso- ries. Additional wet/dry vac accessories may be purchased at your local Sears retail store or Sears/Craftsman Power and Hand Tool Catalog. 16931116990 Caster 17820 2-1/2"x7' Hose...
For the repair or replacement parts you need Call 7 am - 7 prn, 7 days a week 1-800-366-PART (1 8go 366 7278) For in-h0me majorbrand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) For the location of a SearsRepair Service Centerin your area Call 24 hours a day, 7 days a week 1-800-488-1222...