Advertisement
Available languages
Available languages
HARDWARE:
_
1/4-20 Hex Nut
<(_ _:_1_# 1/4-20 x 7/16 Hex Screw
_
[_
8-32 x 1/4 Pan Head Screw
_
8-32 Hex Nut
<_
_/,_,_> 10-16 x 1/2 Sheet Metal Screw
Rivet
REMOVE CHEST FROM ROLL-
AWAY :
• The unit comes with the chest secured to
the inside of the roll-away by either two or
four 1/4-20 bolts.
• Lay the roll-away down on its back. Use
packaging material to protect the paint
finish.
• Remove the securing bolts from the
underside of the roll-away. Save the
screws for mounting the chest to the roll-
away.
• Remove the chest.
CASTER
INSTALLATION:
NOTE: Use adequate
manpower
for this
operation.
• Lay the roll-away down on its back. Use
packaging material to protect the paint
finish.
• Mount both swivel casters on the same
side of the roll-away. The swivel caster
with the brake goes to the front of the
unit.
• Attach casters using 1/4-20 x 7/16 hex
screws and 1/4-20 hex nuts. Wrench
tighten.
• Return the roll-away to its upright
position.
MOUNTING
INTERMEDIATE
CHEST:
• Remove all drawers necessary in order to
attach units. Follow the drawer removal
and installation instructions in the
operation section.
• Position the intermediate chest on the
cabinet. Using the intermediate chest
bottom as a template, mark the mounting
hole locations onto the roll-away top. At
each mark drill a 5/16" diameter hole.
• Bolt the units together using two 1/4-20 x
7/16 hex screws and two 1/4-20 hex
nuts.
• Attach to the top chest with two 1/4-20 x
7/16 hex screws and two 1/4-20 hex
nuts.
• Reinstall all drawers. Follow the drawer
removal and installation instructions in the
operation section.
MOUNTING
CHEST:
• Remove the drawer from the roll-away
(refer to the drawer removal instructions).
• Lift the chest onto the roll-away.
Line up
the holes in the bottom of the chest with
the holes in the top of the roll-away.
• Attach the chest using two 1/4-20 screws
that were used to secure the chest to the
bottom of the roll-away.
• Wrench tighten all screws.
• Replace the drawer (refer to the drawer
installation instructions).
• To remove the chest, reverse the
procedure.
RISER ASSEMBLY:
NOTE: When assembled, the riser
should be the same size, left to right, as
the chest. Use adequate manpower for
this operation.
• Assemble the sides and the back (flange
side up) together using four 8-32 x 1/4
pan head screws and four 8-32 hex nuts.
Finger tighten.
• Position the riser assembly on the roll-
away. Secure using four 10-16 x 1/2
sheet metal screws. Wrench tighten.
• Position the chest on the riser. Secure
using four 10-16 x 1/2 sheet metal
screws. Wrench tighten.
• Wrench tighten the risers four 8-32 x 1/4
pan head screws and 8-32 hex nuts.
st
Back
Side
i
%
Cart
SHELF
INSTALLATION:
• Place the shelf in the roll-away and line
up the holes.
• Insert four plastic rivets through the sides
of the roll-away.
Shelf--.
Rivets.
\.\
Side_
• Press the rivet pin firmly into the rivet
body to secure the shelf.
• The shelf may be removed by prying the
rivet pins out using a screwdriver.
REMOVING
AND INSTALLING
DRAWERS:
• Fully extend the drawer. Then push it
back a quarter of an inch.
• Insert a screwdriver into the slot in the
slide and depress the stop until it clears
the lance. Repeat this procedure for the
other slide. Remove the drawer.
f--
Stop
Lance
3
4
Advertisement
