High Pressure - Craftsman 580.752150 Operator's Manual

WARNING
Contact with muffler area can result in serious
burns.
Exhaustheat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
* DONOT touch hot partsandAVOIDhot exhaustgases.
* Allowequipment t o cool beforetouching.
o Keepat least5 feet (152crn) of clearance on all sidesof
pressure washerincludingoverhead.
, Codeof Federal R egulation (CFR) T itle 36 Parks,Forests, a nd
PublicPropertyrequireequipment p oweredby an internal
combustion engineto havea sparkarrester,rnaintained in
effectiveworkingorder,complyingto USDA Forestservice
standard 5!00-1C or laterrevision.Itsthe Stateof California a
sparkarresteris required undersection4442 of the California
Publicresources code.Otherstatesrnayhavesimilar laws.
NOTE:Always keep the throttle lever in the "Fast" position
when operating the pressure washer.
How to Stop Your Pressure Washer
1. Rebase spray gun trigger and let engine idle for two
minutes.
2. Move throttie to SLOW position, then STOPposition.
WARNING
Backfire, fire or engine damagecould occur.
* DONOTstopenginebymovingchokeleverto "Choke"position.
3. ALWAYSpoint spray gun in a safe direction, press red
button and squeeze spray gun trigger to releaseretained
high water pressure.
iMPORTANT: Spray gun traps high water pressure, even
when engine is stopped and water is disconnected.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
_ nderiying tissues, ieading to serious injury and
)ossibteamputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
• Keephigh pressurehoseconnected to purnpand spray' g un
whilesystemis pressurized.
o ALWAYS pointspray' g un in safedirection,pressred button
and squeeze spraygun trigger,to rebasehigh pressure, e very'
time youstop engine.
How te Use Accessory Tray
The unit is equipped with an accessorytray with piacesto
store your ProjectPro
TM
nozzles, HydroFoam
TM
iauncher, spray
gun and nozzleextension. There is aiso a hook at the front of
the accessorytray to hoid your high pressure hose. Identify
ali accessories with the iiiustration on page 6.
NOTE:The extra hob in the tray is for storing a utiiity brush.
The extra clip in the tray is for storing a turbo nozzie. The
brush and turbo nozzle are NOT included with your pressure
washer. You can buy these items as optional accessories.
1. Mace nozzle extension througil hob on accessory tray,
as shown.
.
3.
4.
.
Placespray gun through hole on accessory tray on right
side of unit.
Insert muiti-coiored ProjectPro
TM
nozzlesin spaces
provided in accessory tray.
Insert HydroFoam
TM
iauncher in space provided in
accessory tray next to the multi-colored ProjectPro
TM
nozztes.
Hang higI1pressure hose on hook attachedto accessory
tray on front of tray as shown.
Hew te Use PrejectPre
TM
Nozzle System
The quick-connect on the nozzle extension aliows you to
switch between three different ProjectPro
TM
system nozzies.
ProjectPro
TM
nozzlescan be changed whiie pressure washer
is running once spray gun trigger Iock is engaged. The
ProjectPro
TM
nozzlesvary the pressure and spray pattern as
shown.
High Pressure
L._._.J
Delicate General Max
40° Yellow 15° Orange 0° Red
2550 PSi 2800 PSi 3100 PSi
2.8 GPM 2.7 GPM 2.3 GPM
13