Fujitsu MAY2036RC Product/Maintenance Manual page 88

Index
I
indicating revision number at factory
shipment .................................................... 6-8
initial diagnosis at time of power-on .............. 5-4
initial seek operation check........................... 6-10
initial self-diagnostic....................................... 6-2
installation....................................................... 5-1
installation requirement .................................. 4-1
installation/removal/replacement.................... 5-2
interface connector.......................................... 4-9
interface connector (SAS plug) signal
allocation................................................. 4-10
interface error ................................................. 7-4
interface test.................................................... 6-4
internal test space............................................ 3-3
L
large capacity .................................................. 1-4
leakage magnetic flux ..................................... 4-6
limitation of bottom-mounting ....................... 4-3
limitation of side-mounting ............................ 4-3
logical data block addressing.......................... 3-8
low noise and low vibration............................ 1-4
low power consumption.................................. 1-4
M
maintenance information ................................ 6-5
maintenance level ........................................... 6-7
maintenance requirement................................ 6-6
maximum temperature .................................... 4-5
microcode downloading.................................. 1-4
MODE SELECT/MODE SELECT
EXTENDED command............................. 5-5
model name and order number ....................... 2-1
mounting drive................................................ 5-3
mounting frame structure................................ 4-3
mounting orientations ..................................... 4-2
mounting procedure........................................ 5-3
mounting requirement..................................... 4-1
mounting screw............................................... 4-3
MTBF ............................................................. 2-5
MTTR ............................................................. 2-6
multi-segment data buffer............................... 1-2
N
noise filter ....................................................... 4-8
note on handling drive .................................... 5-1
note on mounting ............................................ 4-3
O
online self-diagnostic...................................... 6-3
operation check............................................. 6-10
operation test................................................. 6-10
IN-2
outline of troubleshooting procedure ............6-11
P
packaging ........................................................5-2
PAD ................................................................3-7
page code = 1 ..................................................5-8
page code = 3 ..................................................5-5
page code = 7 ..................................................5-8
page code = 21 ................................................5-8
part replacement..............................................6-7
part that can be replaced in field .....................6-6
physical sector allocation ................................3-5
PLO Sync........................................................3-7
port address .....................................................5-3
port addressing................................................1-6
port control parameters .................................5-10
positioning error rate.......................................2-5
power on/off sequence ....................................4-7
power supply requirement ..............................4-7
precaution .......................................................6-5
preventive maintenance ..................................6-6
programmable data block length.....................1-3
R
random/sequential read test.............................6-4
read/write circuit .............................................1-5
read/write error recovery parameter................5-8
ready LED output signal ...............................4-11
reliability.........................................................2-5
reporting result of self-diagnostic and
error indication ..........................................6-3
reserve and release function............................1-3
responses to operation errors ..........................5-4
restriction of use of hazardous substance........1-1
revision number ..............................................6-7
S
SAS standard...................................................1-2
sector format ...................................................3-6
seek test...........................................................6-2
self-diagnostic.................................................6-1
SEND DIAGNOSTIC command ....................6-3
sense data ........................................................7-1
1-1x-xx .................................................... 7-4
3-0C-03.................................................... 7-4
3-1x-xx .................................................... 7-4
4-32-01 .................................................... 7-4
4-40-xx .................................................... 7-4
4-44-xx .................................................... 7-4
4-C4-xx.................................................... 7-4
5-2x-xx .................................................... 7-4
B-44-xx.................................................... 7-4
B-47-xx.................................................... 7-4
B-4B-xx ................................................... 7-4
C141-E230