Table of Contents
Advertisement
PFS
C
ICC-ES #ESR-2542
This book is valuable. In addition to instructing you
on how to install and maintain your appliance, it also
contains information that will enable you to obtain re-
placement parts or accessory items when needed. Keep
it with your other important papers.
This fireplace is approved for use as a wood burning fire-
place or for use with a vented gas log approved to ANS
Z21.60 or Z21.84 standards or for use with a vent-free gas
log heater approved to ANS Z21.11.2 standard.
This wood burning fireplace complies with UL127-CAN/ULS-
S610-M87 standard as a FACTORY BUILT APPLIANCE.
FOR CANADA: The authority having jurisdiction (such
as the municipal building department, fire department,
etc.) should be contacted before installation to deter-
mine the need to obtain a permit.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
For more information, visit www.fmiproducts.com
42" and 50" Wood Burning
Smooth Face with Insulation
Smooth Face with Insulation and
Smooth Face with Insulation and
Smooth Face with Insulation, Bottom
Door Rail and Herringbone Refractory
®
US
SAVE THIS BOOK
Masonry Fireplace
oWner's operaTion and
insTallaTion Manual
(V)g42/50
(V)g42r/50r
Bottom Door Rail
(V)g42H/50H
Herringbone Refractory
(V)g42Hr/50Hr
Advertisement
Table of Contents
Related Manuals for FMI V)G42/50
Summary of Contents for FMI V)G42/50
-
Page 1: Masonry Fireplace
42" and 50" Wood Burning Masonry Fireplace oWner’s operaTion and insTallaTion Manual (V)g42/50 Smooth Face with Insulation (V)g42r/50r Smooth Face with Insulation and Bottom Door Rail (V)g42H/50H Smooth Face with Insulation and Herringbone Refractory (V)g42Hr/50Hr Smooth Face with Insulation, Bottom Door Rail and Herringbone Refractory ®... -
Page 2: Table Of Contents
• This FMI PRODUCTS, LLC fireplace and its • Do not place clothing or other components are safe when installed accord- flammable materials on or near ing to this installation manual. -
Page 3: Specifications
speciFicaTions 42" MODELS SQUARE CHASE-TOP ROUND TOP TERMINATION TERMINATION 2" CHIMNEY AIRSPACE CLEARANCE TO COMBUSTIBLE MATERIAL NO COMBUSTIBLE MATERIAL ON FACE COMBUSTIBLE WALL BOARD " AIR SPACE BACK AND SIDES OUTSIDE AIR MINIMUM 18" TO PERPENDICULAR SIDEWALL GAS LINE KNOCKOUTS HEARTH EXTENSION 66"... - Page 4 speciFicaTions 50" MODELS ROUND TOP TERMINATION SQUARE CHASE-TOP TERMINATION 2" CHIMNEY AIRSPACE CLEARANCE TO COMBUSTIBLE MATERIAL NO COMBUSTIBLE MATERIAL ON FACE COMBUSTIBLE WALL BOARD " AIR SPACE BACK AND SIDES OUTSIDE AIR MINIMUM 18" TO PERPENDICULAR SIDEWALL GAS LINE KNOCKOUTS HEARTH EXTENSION 74"...
-
Page 5: Fireplace Installation
Fireplace insTallaTion SELECTING LOCATION upon a metal or wood panel extending the full width and depth of the fireplace. To determine the safest and most efficient 3. Set the fireplace directly in front of this location for the fireplace, you must take into opening and slide unit back until nailing consideration the following guidelines: flanges touch side framing. - Page 6 Fireplace insTallaTion HEARTH ExTENSION MANTELS A hearth extension projecting a minimum of A mantel may be installed if desired (see 20" in front of and a minimum of 12" beyond Figure 4). Woodwork such as wood trims, each side of the fireplace opening is required mantels or any other combustible material to protect combustible floor construction projecting from the front face must not be...
-
Page 7: Venting Installation
CHIMNEY PIPE pipe and a wire spacer. Pipe sections must be The FMI PRODUCTS, LLC chimney system assembled independently as chimney is installed. consists of 12", 18", 24", 36" and 48" snap-... - Page 8 VenTing insTallaTion Continued USING ELBOW OFFSETS (30E-12DM) 2. Chimney weight above offset rests on return elbow. Straps must be securely 1. To achieve desired offset, you may install nailed to rafters or joists (see Figure 8, combinations of 12", 18", 24", 36" and 48" details a and b).
- Page 9 VenTing insTallaTion Continued PENETRATING ROOF To maintain a 1" clearance to pipe on a roof with a pitch, a rectangular opening must be cut. 1. Determine the center point through which Screws pipe will penetrate roof. 2. Determine the center point of the roof. Pitch is the distance the roof drops over a given span, usually 12".
- Page 10 VenTing insTallaTion Continued Storm Overlap CAUTION: Do not seal open- Collar Shingles Top ings on the rooftop flashing. Fol- Flashing and Sides Only Cone low the installation instructions Nail Only provided with the termination Outer being used. Perimeter of Flashing RTL-10D Stainless Level of...
-
Page 11: Optional Gas Line Installation
VenTing insTallaTion Continued 10 FOOT RULE FINISHING FIREPLACE All flue gas outlet chimney terminations must Combustible materials, such as wallboard, extend a minimum of 3 feet in height above the gypsum board, sheet rock, drywall, plywood, highest point where it passes through the roof etc. -
Page 12: Glass Door Installation
opTional gas line insTallaTion Continued If you install a decorative gas appliance CAUTION: All gas piping (vented gas log), the decorative gas appliance and connections must be tested must comply with the Standard for Decorative Gas Appliance for Installation in Solid Fuel for leaks after the installation Burning Fireplaces, ANS Z21.60 or Z21.84 is completed. -
Page 13: Operation And Maintenance Guidelines
glass door insTallaTion Continued INSTALLING GLASS DOORS track. Door is installed when top door pin snaps into spring clip. Spring clips have been installed but some 2. Repeat step 1 for remaining door. adjustments may be needed. If doors do not close properly or do not appear straight, see If you find doors do not close properly or do Door Adjustment. - Page 14 MainTenance guidelines Continued WARNING: Risk of fire! WARNING: Fireplaces Replace grate with FMI PROD- equipped with glass doors UCTS, LLC model 109496-01 should be operated only with (42" Models) or 109496-02 (50" doors fully opened or doors fully Models) grate only.
-
Page 15: Technical Service
TecHnical serVice You may have further questions about instal- You can also visit FMI PRODUCTS, LLC’s lation, operation, or troubleshooting. If so, web site at www.fmiproducts.com. contact FMI PRODUCTS, LLC at 1-866-328- 4537. When calling please have your model and serial numbers of your heater ready. -
Page 16: Accessories
accessories OPTIONAL OUTSIDE AIR KIT FOR BI-FOLD GLASS DOOR SIDEWALL INSTALLATION - AK4 BDG42 - 42" Black Finish BDG42B - 42" Brushed Brass Finish BDG42P - 42" Platinum Finish BD50 - 50" Black Finish STORM COLLAR - SC2-1 BD50B - 50" Brushed Brass Finish BD50P - 50"...
Need help?
Do you have a question about the V)G42/50 and is the answer not in the manual?
Questions and answers