Fluke Victoreen 960PS-200 Operator's Manual
  1. Manuals
  2. Brands
  3. Fluke Manuals
  4. Power Supply
  5. Victoreen 960PS-200 Operators
  6. Operator's manual
Fluke Victoreen 960PS-200 Operator's Manual

Fluke Victoreen 960PS-200 Operator's Manual

Power supply modules
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
®
Victoreen
960PS-200 & 960PS-210

Power Supply Modules

Operators Manual
March 2005
Manual No. 960PS-200-1 Rev. 2
©2004, 2005 Fluke Corporation, All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies

Advertisement

Table of Contents
loading

Related Manuals for Fluke Victoreen 960PS-200

Summary of Contents for Fluke Victoreen 960PS-200

  • Page 1: Power Supply Modules

    ® Victoreen 960PS-200 & 960PS-210 Power Supply Modules Operators Manual March 2005 Manual No. 960PS-200-1 Rev. 2 ©2004, 2005 Fluke Corporation, All rights reserved. Printed in U.S.A. All product names are trademarks of their respective companies...
  • Page 2 Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 120 Andrews Road Hicksville, New York 11801 516.870.0100 www.flukebiomedical.com/rms...

  • Page 3: Table Of Contents

    Table of Contents Section 1: Introduction....................1-1 General Description ..................1-1 Application ....................1-1 Specifications....................1-1 Receiving Inspection and Storage ............... 1-2 Installation....................1-3 Procedures, Warnings, and Cautions ............1-3 Section 2: Operation....................2-1 960PS-200 Power Supply................2-1 Input Filter....................2-1 DC to DC Converter..................
  • Page 4 (Blank Page)

  • Page 5: Introduction

    Introduction General Description Section 1 Introduction 1.1 General Description The 960PS Power Supply is used to supply power to the modules that are plugged into the 960MB/961MB motherboards. The power supply is mounted outside of the 960CC Card Cage Module, the wall mounted Local Control Unit enclosure, or control room cabinet.

  • Page 6: Receiving Inspection And Storage

    Upon receipt of the unit: 1. Inspect the carton(s) and contents for damage. If damage is evident, file a claim with the carrier and notify Fluke Biomedical, Radiation Management Services at 440.248.9300. 2. Remove the contents from the packing material.

  • Page 7: Installation

    Biomedical. It shall be the owner's or user's responsibility to see to it that the procedures described here are meticulously followed, and especially that WARNINGS and CAUTIONS are heeded. Failure on the part of the owner or user in any way to follow the prescribed procedures shall absolve Fluke Biomedical and its agents from any resulting liability.
  • Page 8 Victoreen 960PS-200 & 960PS-210 Operators Manual (Blank page)

  • Page 9: Operation

    Operation 960PS-200 Power Supply Section 2 Operation 2.1 960PS-200 Power Supply The 960PS-200 supplies three different DC voltage outputs to the 960 modules through the 960MB/961MB motherboard. 115 VAC is connected to terminal strip A3, part of the front panel. The AC line voltage is fed to a bridge rectifier circuit and rectified diodes CR1, CR2, CR3, and CR4.

  • Page 10: 960Ps-210 Power Supply

    Victoreen 960PS-200 & 960PS-210 Operators Manual 2.5 960PS-210 Power Supply The 960PS-210 Power Supply is similar in operation to the 960PS-200, with the exception that it incorporates an additional 24 VDC output, an input voltage sensing circuit, and a common and differential mode choke.

  • Page 11: Maintenance, Calibration And Troubleshooting

    There are no user adjustments on the main 960PS-200. Should the output voltage fall outside of the tolerance specified, the unit must be returned to Fluke Biomedical for repair. Adjustments to the 960PS-210 are limited to the AC Line Monitor Voltage trip point adjustment (R40), mounted on the stand-up circuit board, and the +5 VDC output voltage adjustment (R17).
  • Page 12 Victoreen 960PS-200 & 960PS-210 Operators Manual If a problem develops, verify that the voltages at connection point inputs and outputs are present and that all wiring is secure. Ensure fuse F1 is not open for the 960PS-210 Power Supply. Refer to Appendix B for drawings.

  • Page 13: Appendix A Connector Designations

    Appendix Connector Designations Appendix A Connector Designations A.1 Connector Designations Terminal Designations, 960PS-200 Description AC Line Voltage AC Line Voltage -15 @ 2 A +15 @ 2 A RETURN +5 V Return Sense +5 V@ 10 A + 5 V SENSE CHASSIS GND Terminal Designations, 960PS-21 0 Description...
  • Page 14 Victoreen 960PS-200 & 960PS-210 Operators Manual (Blank page)

  • Page 15: Appendix B: Applicable Drawings And Bill Of Materials

    Schematic Diagram B.2 Applicable Bill of Materials The 960PS-200 Power Supply is manufactured specifically for Fluke Biomedical by Adtec Power, Inc. and the 960PS-210 Power Supply is manufactured specifically for Fluke Biomedical by Deltron, Inc. These devices are not user serviceable, and sub-component bill of materials is not available. The unit must be...
  • Page 16 Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 120 Andrews Road Hicksville, New York 11801 516.870.0100 www.flukebiomedical.com/rms...

This manual is also suitable for:

Victoreen 960ps-210

Table of Contents