Table of Contents
Advertisement
Available languages
Available languages
Howto Use Selector Nozzle
The selector nozzle allows you to switch between five
different spray pattern nozzles. Spray patterns can be
changed while pressure washer is running once spray gun
trigger safety lock is engaged.The spray patterns vary as
shown below.
_i_WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER changespraypatterns withoutthetriggerlockedon the
spraygun.
• DONOT twist selectornozzle whilespraying.
Follow these instructionsto changenozzle patterns:
1.
Select desired spray pattern:
•
MAX - For stubborn or hard to reach surface such
as second story surfaces, paint removal, oil stains,
rust removal or other stubborn substances (tar,
gum, grease, wax, etc.).
•
GENERAL- For most all purpose cleaning such as
home siding, brick patios, wood decks, driveways
and sidewalks, garage floors, etc..
•
DELICATE - For gentle cleaning of cars/trucks,
boats, RV's, patio furniture, lawn equipment, etc..
•
FLUSH- For quick high flow clean up and long
reach cleaning of second story siding and windows.
•
SOAP- For general soap applications or to launch
soap to second story siding and windows.
2.
Push button on selector nozzle,nozzle dial will pop up.
3.
Turn dial until desired spray pattern lines up with button
on selector nozzle.
4.
Push dial in until it locks into place.
Usage Tips
*
For most effective cleaning, keep selector nozzle from
8 to 24 inches (20 to 61 cm) away from cleaning surface.
*
if you get selector nozzletoo close, especially using a
high pressure spray pattern nozzle, you may damage
surface being cleaned.
*
DONOT get closer than 6 inches (15 cm) when cleaning
tires.
2-1N-1Soap System
A WARNING ChemicalBurn Hazard.
_
Chemicals could cause burns resulting in death,
serious injury, and/or property damage.
• DONOT usecausticliquidwith pressure washer.
• UseONLYpressure washersafedetergents/soaps. Follow all
manufacturers instructions.
Cleaning and Applying Detergentwith the
Project Pro® PerfectlVIWMSiphon
To apply undiluted detergent using the blue
PerfectMix
TM
siphon, follow these steps:
1.
Review use of selector nozzle.
2.
Attach PerfectMWMsiphon hose to
pump and PerfectMix
TM
concentrate
bottle.
i
NOTICE
Contact with the hot muffler could damage
detergent siphoning tube.
• When inserting the siphon into a detergent solution bottle, route
the tube so as to keepit from inadvertently contacting the hot
muffler.
3.
Make sure SOAPspray pattern nozzle is selected on
selector nozzle.
NOTICE Detergent cannot be applied with the MAX,
GENERAL,DELICATE or FLUSHspray pattern nozzles.
4.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE
You must attach all hoses before you start the
engine.
• Starting the engine without all the hoses connected and without
the water turned ON could damage the pump.
• Damageto equipment resulting from failure to follow this
instruction will void warranty.
5.
Start engine following instructions How to Start Your
Pressure Washer.
6.
Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
7.
Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapplyas needed to prevent
surface from drying. DO NOTallow detergent to dry on
(prevents streaking).
15
Advertisement
Table of Contents
