Download Print this page

Whirlpool XHP1550WL Installation Instructions Manual page 3

Installation instructions
Hide thumbs

Advertisement

iil!!i!!E_,_,_ii!!i!!!_i_c_iiiii:i_,_jjii_i!!i!!_,
ii!_Siii::_;;i::!i_!ili_iii:1_i_!!_i_ii:_
'_?"iO_ii;_iiii_
¸_' iii:::_'_;:!!:!!!_,_::::lii,_lii!_i!_Siiii:_i_i!:!!iiii
IMPORTANT: If your washer and dryer are already installed, they
must be uninstalted.
If you need to uninstatl your washer or dryer, see your Installation
Instructions that came with your model for tools required.
UninstaHing
Your Washer
Excessive Weight Hazard
Use two or more peopJe to move and uninstall washer.
Failure to do so can result in back or other injury.
1. Turn off the hot and cold water faucets.
2. Unplug the power supply cord or disconnect
power.
3. Slowly loosen the fill hoses at the faucets to relieve the water
pressure. Use a sponge or towel to absorb the released water.
4. Remove the hot and cold fill hoses from the back of the
washer. Drain the water from the hoses into a bucket.
5. Squeeze the ears of the drain hose clamp with pliers to open
and slide the clamp down the hose. Disconnect the drain
hose from the washer and drain any water in the hose into
a bucket.
6. Putt the washer away from walt so it can be tipped on
its back.
7. Protect the floor with
a large piece of
cardboard cut from
the pedestal carton.
Lay the washer on
its back (make sure
that the power
1211_ _
supply cord is not
under the washer) so
that the cardboard is
15"
\\
under the entire
(38.1cm)
lower back edge of
the washer. An
additional small amount of water will drain out of the washer
when it is tipped back.
8. Go to "Installing the Pedestal" section.
Ininstalling
Your Electric
Dryer
"a,
Electrical
Shock Hazard
Disconnect power before servicing.
Replace all panels before operating,
Failure to do so can result in death or electrical shock.
Excessive Weight Hazard
Use two or more peopJe to move and uninstall dryer.
Failure to do so can result in back or other injury.
3. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
4. Pull the dryer away from wall so that it can be tipped onto its
back.
5. Protect the floor with a
large piece of
cardboard cut from the
pedestal carton. Lay
the dryer on its back
(make sure that the
power supply cord is
12"
not under the dryer) so
(30.5cm)\
that the cardboard is
:_
under the entire lower
15"
'\
back edge of the dryer.
(38.1cm)
6. Go to "Installing the
Pedestal" section.
Uninstalling
Your Gas Dryer
1. Unplug the power supply cord or disconnect
power.
2, Turn off the gas supply.
Excessive Weight Hazard
Use two or more peopJe to move and uninstall dryer.
Failure to do so can result in back or other injury.
3=
4=
5=
6.
7=
Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
Disconnect the flexible gas supply line from the dryer. Put a
piece of tape over the open ends of the gas line connection
fittings.
Putt the dryer away from wall so that it can be tipped onto
its back.
Protect the floor with a
large piece of
cardboard cut from the
pedestal carton. Lay
the dryer on its back
(make sure that the
power supply cord is
not under the dryer) so
that the cardboard is
under the entire lower
back edge of the dryer.
Go to "Installing the
Pedestal" section.
(30.5 cm)\_
_
15"
\,
(38 1 cm)\
....
_I
t_t_
.......
1. Unplug the power supply cord.
2. Disconnect wiring if dryer is direct wired.

Advertisement

loading