Advertisement
Available languages
Available languages
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground
prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Washer
won't run, fill, rinse, or agitate;
washer
stops
m is the power cord plugged into a grounded 3 prong
outlet?
Plug power cord into a grounded 3 prong outlet.
I
Are you using an extension
cord? Do not use an extension
cord.
m is the indicator on the Timer knob properly lined up with a
cycle? Turn the Timer knob to the right slightly and pull knob
out to start.
II
Are the water inlet valve screens clogged?
Turn off the
water and remove inlet hoses from the washer. Remove any
accumulated
film or particles. Reinstall hoses, turn on water,
and check for leaks.
Are both the hot and cold water faucets
turned on?
Turn on the water.
II
II
II
is the water inlet hose kinked?
Straighten the hoses.
Has a household fuse blown, or has a circuit
breaker
tripped?
Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
is the washer in a normal
pause in the cycle? The washer
pauses for about 2 minutes during certain cycles. Allow the
cycle to continue. Some cycles feature periods of agitation
and soak.
II
II
Did you wash a large load? Was the wash load tightly
packed?
Wash smaller loads and load in loose heaps.
is the lid open? The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
Washer
won't
drain
or spin, or loads are wet
m is the drain hose clogged,
or the end of the drain hose
more than 96" (2.4 m) above the floor? See "installation
instructions"
for proper installation of drain hose.
is the lid open? The lid must be closed during operation.
Washer will not agitate or spin with the lid open.
is there excessive
sudsing? Always measure detergent.
Follow manufacturer's
directions.
If you have very soft water,
you might need to use less detergent.
Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).
is the drain hose length fed too far down the drain pipe?
Use the drain hose form to raise the end of the hose. The
hose should be no more than 4.5" (113 mm) down the pipe.
Secure drain hose to drain pipe.
r;
;
r;
r
;
r
r;r_
Washer
continues
to fill or drain;
cycle
seems
stuck
;
r;
r
..................................... r r;
r;
r;
r
is the top of drain hose lower than the water level in
washer?
The top of the hose must be higher than the water
level in the washer for proper operation. See "installation
instructions."
m Does the drain hose fit too tightly in the standpipe,
or is it
taped to the standpipe?
The drain hose should be loose yet
fit securely. Do not seal the drain hose with tape. The hose
needs an air gap. See "installation Instructions."
Wash/Rinse
temperature
not what
I selected
Are the hot and cold water
inlet hoses reversed?
See
"installation instructions"
for more information.
Does the Hot or Warm wash seem cooler than you
expected?
Hot and warm temperatures
are controlled by the
washer and may be cooler than your previous washer. This is
normal. The cooler temperatures
save energy while providing
good cleaning.
r
Garments
damaged
II
Check the following:
Empty pockets, zip zippers, snap
or hook fasteners before washing. Tie strings and sashes
to avoid tangling. Were items damaged before washing?
Mend rips and broken threads in seams before washing.
8
Advertisement
