Related Manuals for Smart Technologies X-Port 20 Switch (XP20-2000i-B
Summary of Contents for Smart Technologies X-Port 20 Switch (XP20-2000i-B
- Page 1 X-Port™ 20 Switch (XP20-2000i-B) Installation Guide for any 2000i Equipped with an NEC VT465 or VT560 Projector 99-00539-00 Rev B0...
- Page 2 Copyright Notice © 2004 SMART Technologies Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
-
Page 3: Table Of Contents
Contents Installing an X-Port 20 Serial/Video Switch in a 2000i-DVS ............1 To mount the X-Port 20 switch ............................1 To connect the X-Port 20 switch ............................5 To connect a guest laptop ...............................8 Customer Support ..........................10 Contacting SMART Technical Support .........................10 General Inquiries ................................10 Returning Defective Merchandise ..........................10 Warranty Shipping Charges ............................10... - Page 4 99-00539-00 Rev A0...
-
Page 5: Installing An X-Port 20 Serial/Video Switch In A 2000I-Dvs
Installing an X-Port™ 20 Switch in a 2000i with an NEC VT465 or VT560 Projector This kit contains: Tools required (but not included): • an antistatic wrist strap • Phillips® screwdrivers • an X-Port 20 switch which includes two stacked circuit •... - Page 6 Make sure the casters are locked and all four anti-tip feet are extended. Remove the stickers covering the lower DB9 opening and the upper HD15 opening. Place the supplied serial (computer) label over the lower opening and the supplied video label over the upper opening, as illustrated below. Upper HD15 Opening Video Label Lower DB9 (Computer)
- Page 7 Carefully swing the electronics tray down so it hangs vertically. Rear View of 2000i with Back Legs Removed for Clarity Electronics Tray (Open Position) Open Electronics Tray Familiarize yourself with the components of the supplied X-Port 20 switch. In particular, take note of the I²C input jacks and the gender changer on the left side of the bottom card.
- Page 8 Unplug the DB9 cable from the serial controller and plug it into the gender changer on the bottom card of the X-Port 20 switch. Unplug DB9 cable Serial Controller (From Resident Computer Serial Port) X-Port 20 Switch Plug DB9 cable into gender changer on bottom card (connector not shown in image) Rerouting the DB9 Cable to the X-Port 20 Switch...
-
Page 9: To Connect The X-Port 20 Switch
To connect the X-Port 20 switch Attach the loose end of the DB9 female-to-female ribbon cable to the serial controller using the two supplied machine screws. Secure the ribbon cable and serial cable in place, as shown below, using two of the supplied tie wraps. Machine Screws (x 2) Serial Controller Loose End of... - Page 10 Connect the supplied 6" (15.2 cm) I²C cable between the audio amplifier (either I²C jack) and the empty I²C jack on the bottom card of the X-Port 20 switch. Supplied 6" (15.2 cm) I²C Cable Audio Amplifier NOTE: Connect the I²C cable to the empty I²C jack on the bottom card of the X-Port 20 switch.
- Page 11 Locate the tie-wrapped bundle of cables running along the underside of the cabinet. In this bundle is a video cable (labeled RBG 1 IN) that connects directly to the RGB IN port on the projector. Disconnect this cable from the back of the projector, carefully cut the tie wraps that hold the bundle together with a pair of wire cutters or sturdy scissors, and connect the cable to the Video IN port on the top card of the X-Port 20 switch.
-
Page 12: To Connect A Guest Laptop
Swing the electronics tray back to its original position, and insert the two button head screws that you removed earlier. IMPORTANT Before you close the electronics tray, ensure all cables are routed neatly. Use the supplied tie wraps to bundle the cables. To connect a guest laptop Attach the supplied guest laptop cable bundle to the rear of the 2000i as follows: •... - Page 13 Turn on the guest laptop. If it’s still unplugged, plug in the 2000i and press the Lamp On button on the Control Panel. Press the Guest Laptop button on the Control Panel to switch to the guest laptop video source. If the initialization screen does not appear on the interactive whiteboard Try activating the external video port on your guest laptop.
-
Page 14: Customer Support
General Inquiries Main Switchboard: 1.888.42.SMART (toll-free in Canada/U.S.) or +1.403.245.0333 (all other countries) Fax: +1.403.228.2500 E-mail: info@smarttech.com Address: SMART Technologies Inc. Suite 300, 1207 – 11th Avenue SW Calgary, AB CANADA T3C 0M5 Installing an X-Port 20 Switch in a 2000i...
Need help?
Do you have a question about the X-Port 20 Switch (XP20-2000i-B and is the answer not in the manual?
Questions and answers