Related Manuals for Smart Technologies X-Port 20 Switch XP20-2000i
Summary of Contents for Smart Technologies X-Port 20 Switch XP20-2000i
-
Page 1: Installation Guide
X-Port 20 Switch ™ (XP20-2000i) Installation Guide for a 2000i with an NEC MT860 or NEC MT1060 Projector 99-00486-00 Rev B0... - Page 2 Copyright Notice © 2004 SMART Technologies Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
-
Page 3: Table Of Contents
Contents Installing the X-Port 20 Switch in a 2000i-DV/DVX......1 To install the X-Port 20 switch ..............1 To connect a Guest Laptop............... 7 Contacting SMART Technical Support ..........8 General Inquiries ................... 8 Warranty ......................8 99-00486-00 Rev B0... - Page 4 99-00486-00 Rev B0...
-
Page 5: Installing The X-Port 20 Switch In A 2000I-Dv/Dvx
Installing the X-Port 20 in a 2000i with an NEC MT860 or MT1060 Projector These instructions show you how to: • install an X-Port 20 switch in a 2000i that’s equipped with an NEC 860 or 1060 projector • connect a guest laptop The X-Port 20 unit is an RS-232 serial switch for connecting a laptop to the interactive whiteboard. - Page 6 3. Remove the sticker covering the lower DB9 opening. Place the supplied label over this opening. DB9 Connector Opening (Sticker Removed) 2000i (Back Leg Removed Supplied Label for Clarity) 4. While propping up the Electronics tray with one hand (so it doesn’t fall suddenly), remove the two button head screws on either side, using the 5/32"...
- Page 7 5. Carefully swing the Electronics tray down so it hangs vertically. Open Electronics Tray 6. Install the X-Port 20 switch on the studs in the Electronics Tray. Using a Phillips No. 1 screwdriver, secure it in place with the supplied screws and washers. Stud (x 4) X-Port 20 Switch Installing the X-Port 20 Switch in the Electronics Tray...
- Page 8 7. Unplug the DB9 cable from the serial controller and plug it into the gender changer on the X- Port 20 switch. Unplug DB9 cable from here Serial Controller X-Port 20 Switch Plug DB9 cable into gender changer 8. Attach the loose end of the DB9 female-female ribbon cable to the serial controller using the supplied screws.
- Page 9 9. If you don’t have a Room Control Module installed, attach the supplied MOD6 cable to the audio amplifier and the X-Port 20 switch. Then go to step 12. Supplied MOD6 Cable Audio Amplifier 10. If you have a Room Control Module installed, disconnect the MOD6 cable (that runs between the audio amplifier and the Room Control Module) from the audio amplifier and connect it to the X-Port 20 switch (either of the two MOD6 connectors is fine).
- Page 10 11. Connect the supplied MOD6 cable to the audio amplifier and the X-Port 20 switch. Supplied MOD6 Cable 12. Swing the Electronics tray back to its original position, and insert the two button head screws that you removed earlier. Avoid pinching any cables. 13.
-
Page 11: To Connect A Guest Laptop
To connect a Guest Laptop 1. Extend the laptop end of the umbilical from the rear of the 2000i until it reaches the laptop/videoconferencing shelf. 2. Connect the three cables that comprise the laptop end of the umbilical − the Computer 2 Audio, Computer 2 Video and Computer 2 Serial −... -
Page 12: Customer Support
Main switchboard: toll-free at 1.888.42.SMART or outside North America at +1.403.245.0333 Fax: 403.228.2500 E-mail: info@smarttech.com Our address: SMART Technologies Inc. Suite 300, 1207 − 11th Avenue SW Calgary, AB CANADA T3C 0M5 Warranty The X-Port 20 switch is covered by a one-year parts and labor warranty. Customers must return any defective merchandise to an authorized service center as directed by the distributor, dealer or manufacturer.
Need help?
Do you have a question about the X-Port 20 Switch XP20-2000i and is the answer not in the manual?
Questions and answers