1. Manuals
  2. Brands
  3. Smart Technologies Manuals
  4. Projector
  5. SMART UF75
  6. Maintenance instructions manual

Smart Technologies SMART UF75 Maintenance Instructions Manual

Hide thumbs Also See for SMART UF75:

Advertisement

Table of Contents

See also: User Manual
P L E A S E T H I N K B E F O R E Y O U P RI NT

Knowledge base

Maintaining your SMART
UF75 projector
Maintaining your interactive whiteboard
For information on maintaining your interactive whiteboard, see your SMART Board™
interactive whiteboard user's guide (smarttech.com/support).

Cleaning the projector

WARNING
Cleaning a wall-mounted projector can result in a fall or injury. Use caution when
climbing a ladder, and consider removing the projector from its wall-mounting
bracket to clean it or to replace the projector lamp.
CAUTIONS
•
Never touch the mirror with your hands or a brush, and do not scrub the
surface of the mirror with the supplied cleaning cloth. Instead, use the
supplied cleaning cloth to clean the mirror gently, and do not put any cleaning
solvents on the cloth or the mirror.
•
Before you clean the projector, press the Power button twice on the Extended
Control Panel (ECP) or remote control to put the system into Standby mode,
and then allow the lamp to cool for at least 30 minutes.
•
Do not spray cleaners, solvents or compressed air directly on the projector.
Do not use spray cleaners or solvents near any part of the projector because
they can damage or stain the unit. Spraying the system could spread a
chemical mist on some of the projector's components and lamp, resulting in
damage and poor image quality.
•
Do not allow liquids or commercial solvents of any kind to flow into the
projector base or head.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SMART UF75 and is the answer not in the manual?

Questions and answers

Related Manuals for Smart Technologies SMART UF75

Summary of Contents for Smart Technologies SMART UF75

  • Page 1: Knowledge Base

    P L E A S E T H I N K B E F O R E Y O U P RI NT Knowledge base Maintaining your SMART UF75 projector Maintaining your interactive whiteboard For information on maintaining your interactive whiteboard, see your SMART Board™ interactive whiteboard user’s guide (smarttech.com/support).

  • Page 2: Removing And Replacing The Projector Lamp Module

    KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R IMPORTANT •...
  • Page 3 Wear protective eyewear while changing the lamp. Failure to do so can cause injuries including loss of eyesight if the lamp shatters or bursts. – Use only replacement lamps approved by SMART Technologies. Contact your authorized SMART reseller (smarttech.com/where) for replacement parts.
  • Page 4 KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R 4.
  • Page 5 KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R 8.
  • Page 6 KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R NOTE You should be able to place the lamp module into the projector easily without applying much force.
  • Page 7 KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R To remove the filter 1.
  • Page 8 KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R 2.
  • Page 9 KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R To adjust the vertical Loosen or tighten the lower screws on the projector mounting plate, turning each keystone of the projected...

  • Page 10: To Center Projected Image

    10 | KN O W L E D G E B AS E – M A I N T A I NI NG Y O U R S MA R T U F 7 5 P RO J E C T O R To center the projected If the image is off center, use a wrench to turn the adjustment screw on the image...
  • Page 11 © 2011 SMART Technologies ULC. All rights reserved. SMART Board, smarttech, the SMART logo and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. All third-party product and company names may be trademarks of their respective owners. Contents are subject to change without notice. 05/2011.

Table of Contents