Hitachi L300P Series Instruction Manual Supplement page 12

L300P Supplement
Function mode
Code Function name
Intelligent input1a/b(NO/NC)
C011
selection
Intelligent input2a/b(NO/NC)
C012
selection
Intelligent input3a/b(NO/NC)
C013
selection
Intelligent input4a/b(NO/NC)
C014
selection
Intelligent input5a/b(NO/NC)
C015
selection
Input FWa/b(NO/NC)
C019
selection
C021 Intelligent output 11 setting
C022 Intelligent output 12 setting
C026 Alarm relay output setting
C027 FM selection
C028 AM selection
C029 AMI selection
C031 Intelligent output 11a/b
C032 Intelligent output 12a/b
C036 Alarm relay output a/b
Overload advance
C040
signal output mode
C041 Overload notice level
Frequency arrival setting for
C042
accel.
Arrival frequency setting for
C043
decel.
C044 PID deviation setting level
Electorical thermal protection
C061
warning level setting
C070 Data command
Communicating
C071
speed
C072 Communication code
C073 Communication bit
C074 Communication parity
C075 Communication stop bit
C078 Communication waiting time
C081 O adjustment
C082 OI adjustment
C083 O2 adjustment
C085 Thermistor adjustment
C086 AM offset adjustment
C087 AMI adjustment
C088 AMI offset adjustment
NOTE (3) : See Page 1 (RMD : Output signal for RUN Command Source)
00(RUN:running)/01(FA1:Frequency arrivaltype1 signal)/
02(FA2:frequency arrival type2 signal)/
03(OL:Overload advance notice signal)/
04(OD:Output deviation for PID control)/
05(AL:Alarm signal)/06(FA3:Only setting frequency)/
08(IP:On instantaneous stop/09(UV:Under voltage/
11(RNT:RUN time over/
12(ONT:ON time over)/13(THM:thermal caution)/
27(RMD: RUN command source)
00(Output frequency)/01(Output current) /
03(Digital output frequency)/04(Output voltage)/
05(Output electric
frequency)
00(Output frequency)/01(Output current)/04(Output voltage)/
05(Output electric
frequency)
00(Output frequency)/01(Output current)/04(Output voltage)/
05(Output electric
frequency)
notice 00(On accel. And decel, constant speed)/
01(Only constant speed)
02(operator)/03(RS485)/04(option1)/05(option2)
transmission
02(TEST)/03(2400bps)/04(4800bps)/05(9600bps)/06(19200bps)
00(no parity name)/01(even parity)/02(odd parity)
0.-9999./1000-6553(10000-65530)
0.-9999./1000-6553(10000-65530)
0.-9999./1000-6553(10000-65530)
Setting range
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
NOTE (3)
power)/06(thermal load
power)/06(thermal load
power)/06(Thermal load
00(NO)/01(NC)
00(NO)/01(NC)
00(NO)/01(NC)
0.0-2.0*rated current(A)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.0-100.0(%)
0.-100.(%)
1. -32.
7(7bit)/8(8bit)
1(bit)/2(bit)
0.-1000.(ms)
0.0 - 1000.
0.0 - 10.0(V)
0. - 255.
0. - 20.0(mA)
10
Explanation of functions
LBRM/HFBM
Initial Data
00
00
00
00
00
00
27
00
05
00
rate)/07(LAD
rate)/07(LAD 00
rate)/07(LAD 00
00
00
00
01
Inverter rated
current
0.00
0.00
3.0
80.
02
04
1.
7
00
1
0.
Setting on
forwarding
Setting on
forwarding
Setting on
forwarding
105.0
0.0
80
4.0
LFU/HFU
Initial data
00
00
01
00
00
00
01
00
05
00
00
00
00
00
01
01
Inverter
rated
current
0.00
0.00
3.0
80.
02
04
1.
7
00
1
0.
Setting on
forwarding
Setting on
forwarding
Setting on
forwarding
105.0
0.0
80
4.0