Eeprom Address Map - Epson FX-980 Service Manual

FX-980

7.1 EEPROM Address Map

This chapter provides EEPROM Address Map for FX-980 and
component layouts and circuit diagram for the C276 Main Board.
NOTE: The data of two or more bytes are assigned in such was as
lower byte to lower address, higher byte to higher address.
Table 7-1. EEPROM Address Map (1/7)
Address Data
00H, 01H (reserved)
Area 1
0: PC437
02H, 03H Character
table 1: PC850
selection
2: PC860
3: PC863
4: PC865
5: PC861
6: BRASCII
7: Abicomp
8: ISO Latin 1
9: Roman 8
10:PC437 Greek
11:PC852
12:PC853
13:PC855
14:PC857
15:(reserved)
16:PC866
17:PC869
18:ISO Latin 1T
37:Italic U.S.A.
38:Italic France
39:Italic Germany
40:Italic U.K.
Appendix
Q-pit
Data Format
data
0000H
19:ISO 8859-7
0000H
20:MAZOWIA
21:Code MJK
22:Bulgaria
23:Estonia
24:PC774
25:ISO 8859-2
26:PC866 LAT
27:PC866 UKR
28:Hebrew 7
29:Hebrew 8
30:PC862
31:PCAPTEC
32:PC708
33:PC720
34:PCAR864
35:PC858
36:ISO 8859-15
41:Italic Denmark I
42:Italic Sweden
43:Italic Italy
44:Italic Spain I
EEPROM Address Map
Table 7-2. EEPROM Address Map (2/7)
Address
04H, 05H Page length for rear
tractor
06H, 07H Page length for front
tractor
Factory
08H, 09H Page length for CSF
setting
bin 1
0000H
0AH, 0BH Page length for CSF
bin 2
0000H
0CH, 0DH TOF adjustment
(PC437)
value for rear tractor
0EH, 0FH TOF adjustment
value for front tractor
10H, 11H TOF adjustment
value for CSF bin 1
12H, 13H TOF adjustment
value for CSF bin 2
14H, 15H TOF adjustment
value for rear manual
insertion
16H, 17H TOF adjustment
value for front
manual insertion
18H, 19H Bottom margin for
rear tractor
*: Minimum value depends on the value for 2DH - 2EH.
Data Data Format
1 to 22 x 432 (by 1/432 inch)
0000H: 11 inch (default)
1 to 22 x 432 (by 1/432 inch)
0000H: 11 inch (default)
1 to 22 x 432 (by 1/432 inch)
0000H: 11 inch (default)
1 to 22 x 432 (by 1/432 inch)
0000H: 11 inch (default)
-144 to 432
(4.2 mm to 8.5 mm + 1 inch,
by 1/432 inch) *
-144 to 432
(4.2 mm to 8.5 mm + 1 inch,
by 1/432 inch) *
-144 to 432
(4.2 mm to 8.5 mm + 1 inch,
by 1/432 inch) *
-144 to 432
(4.2 mm to 8.5 mm + 1 inch,
by 1/432 inch) *
-144 to 432
(4.2 mm to 8.5 mm + 1 inch,
by 1/432 inch) *
-144 to 432
(4.2 mm to 8.5 mm + 1 inch,
by 1/432 inch) *
1 to 22 x 432 (by 1/432 inch),
0000H: 11inch (default)
Revision A
Q-pit Factory
data setting
0000H 0000H
(11 inch) (11 inch)
0000H 0000H
(11 inch) (11 inch)
0000H 0000H
(22 inch) (22 inch)
0000H 0000H
(22 inch) (22 inch)
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
(8.5 mm) (8.5 mm)
0000H 0000H
(11 inch) (11 inch)
60