Operation - Central Pneumatic FP202800 Operating Instructions And Parts Manual

Compresores Sin Aceite
Guía de diagnóstico de averías (Continuación)
Problema Posible(s) Causa(s)
Exceso de humedad en 1. Demasiada agua en el tanque
el aire de descarga
2. Humedad elevada
El compresor funciona 1. Presostato defectuoso
en forma continua y la 2. Válvula de seguridad defectuosa
válvula de seguridad se
abre cuando aumenta
la presión
Arranques y paradas 1. Demasiada condensación en el
excesivas tanque
2. Conexiones flojas (accesorios, tubería,
etc.)
Acción a tomar
1. Drene el tanque, incline el tanque para eliminar la
humedad
2. Llévelo a un área menos húmeda, utilice un filtro de
aire de línea
Nota: La condensación de agua no es una causa para
el malfuncionamiento del compresor.
1. Cambie el interruptor de presión
2. Cambie la válvula de retención con un repuesto
original
1. Drene con más frecuencia
2. Revise todas las conexiones con una solución de agua
y jabón. Si se detecta una fuga, apriete. O quite la
conexión y aplique cinta para tuberías a las rocas y
vuelva a armar.
22 Sp
Installation
(Continued)
ON/OFF Switch
Do not use
a grounding adapter with this product!
2. If repair or replacement of cord or plug
is necessary, do not connect grounding
wire to either flat blade terminal. The
wire with insulation having an external
surface that is green (with or without
yellow stripes) is the grounding wire.
Never
connect
green (or green and yellow) wire to a live
terminal.
3. Check with a qualified electrician or
serviceman if grounding instructions
Drain Valve
are not completely understood, or if in
doubt as to whether product is
properly grounded. Do not modify
Figure 2 - Unit Identification
plug provided; if it will not fit outlet,
have proper outlet installed by a
BEFORE FIRST STARTUP
qualified electrician.
BREAK-IN PROCEDURE
(Complete this procedure before using
Overheating, short circuiting and fire
compressor for the first time. Once
damage will result from inadequate
completed, it is not necessary to
wiring, etc.
repeat.)
1. Do not attach a hose or any other

Operation

fitting to the compressor.
Definition of Terms 2. Turn on/off switch to OFF position.
ASME Safety Valve - This valve 3. Plug in power cord.
automatically releases air if the tank
4. Turn on/off switch to ON position.
pressure exceeds the preset maximum.
Allow compressor to run for 5
Handle - Designed to move the minutes.
compressor.
5. Turn on/off switch to OFF position.
Drain Valve - This valve is located on
6. Unplug power cord.
the bottom of the tank. Use this valve
BEFORE EACH STARTUP
to drain moisture from the tank daily
OPERATING PROCEDURE
to reduce the risk of corrosion.
1. Connect air hose to open port
Reduce tank pressure below 10 psi,
located below pressure gauge.
then drain moisture from tank daily to
2. Attach the necessary fitting or tool
avoid tank corrosion. Drain moisture
to open end of air hose.
from tank by opening the drain valve
3. Turn on/off switch to OFF position.
located underneath the tank.
4. Plug in power cord.
LUBRICATION
5a. If using inflation needles/nozzles:
This is an oilless product and DOES
Attach air hose with inflation
NOT require lubrication to operate.
fitting to the object you are going
Extension cords for 120V/2.5 Amp Unit
Length of Cord (ft) 25 50 100
Gauge of Cord 18 18 16
FP202800, FP202900, FP202897, FP202999DB,
FP202999DQ, and FP202899TT
Handle
Pressure Gauge
Safety Valve
to inflate. While holding inflation
fitting firmly in place, turn on/off
switch to ON position. Allow
compressor to inflate the object.
Turn off compressor and remove
inflation fitting.
5b. If using tire chuck or tool: Once
chuck or tool is attached to air
hose, turn on/off switch to ON
position and allow compressor to
run until it automatically shuts off.
When using tire chuck to inflate
tires, observe gauge reading on
compressor and periodically check
tire pressure with a separate tire
gauge to prevent overinflation.
On/Off cycling of compressor
In the ON position, the compressor
pumps air into the tank. When a shut-
off (preset "cut-out") pressure is
reached, the compressor automatically
shuts off.
If the compressor is left in the ON
position and air is depleted from the
tank by use of a tire chuck, tool, etc.,
the compressor will restart
automatically at its preset "cut-in"
pressure. When a tool is being used
150 200 250 300 400
14 14 12 12 10
3
500
10