Sound Setting; Adjusting Balance (Between Left And Right)/ Fader (Between Front And Rear)/Defeat; Setting The Bass Control (Cda-9811 Only); Setting The Treble Control (Cda-9811 Only) - Alpine CDA-9811 Owner's Manual

Sound Setting

SOURCE/ BAND/
POWER TEL. Rotary encoder
f
g
T.CORR/
X-OVER
MX
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat
1
Press Rotary encoder repeatedly to choose the
desired mode.
Each press changes the modes as follows:
→ BALANCE → FADER → DEFEAT →
SUBWOOFER* 1
VOLUME → SUBWOOFER*
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
Press g or f after selecting the Subwoofer mode,
and the subwoofer output phase is toggled NORMAL
(PHASE 0°) or REVERS (PHASE 180°).
• If the Rotary encoder is not pressed within 5 seconds after
selecting the BALANCE, FADER, DEFEAT or SUBWOOFER
mode, the unit automatically returns to normal mode.
• If you set the 2WAY/3WAY switch (page 38) to 3WAY, you cannot
adjust the FADER mode on the CDA-9815/CDA-9813.
1
* When the subwoofer mode is set to OFF, its level and phase cannot
be adjusted.
2
Turn the Rotary encoder until the desired sound
is obtained in each mode.
By setting Defeat ON, previously adjusted settings of
BASS, TREBLE and EQ will return to the factory defaults
and MX is turned off.
• Depending on the connected devices, some functions and display
indications do not work.
• When you press DISP/B.OUT, you can switch the Level Indicator
display to the AUDIO Adjustment display on the CDA-9815/CDA-
9813 only. For details, see "Changing the Audio Level Display
Pattern" (page 7).

Setting the Bass Control (CDA-9811 only)

You can change the bass frequency emphasis to create your own tonal
preference.
1
Press CENTER f to select the Bass (bass center
frequency) Control mode.
BASS → TREBLE → normal mode → BASS
Preset buttons
(1 through 6)
EQ
(CDA-9815/CDA-9813)
CENTER f
(CDA-9811)
1
*2
2-1
Setting the bass center frequency:
Press g or f to select the desired bass center
frequency.
60Hz ↔ 70Hz ↔ 80Hz ↔ 90Hz ↔ 100Hz ↔ 130Hz ↔ 150Hz
↔ 200Hz ↔ 60Hz
The displayed bass frequency is emphasized
.
*2
2-2
Setting the bass band width (Q-Factor):
Press BAND/TEL. to select the desired bass band
width.
→ B. Width1 → B. Width2→ B. Width3 → B. Width4
......................................
(Narrow)←
Changes the boosted bass band width to wide or narrow.
A wide setting will boost a wide range of frequencies
above and below the center frequency. A narrower setting
will boost only frequencies near the center frequency.
2-3
Setting the bass level:
Turn the Rotary encoder to select the desired
bass level (–7~+7).
You can emphasize or weaken the bass frequency.
• If no buttons are pressed within 15 seconds, the bass control setting
will be turned off automatically.
• The bass level settings will be individually memorized for each
source (FM, AM, XM, CD, etc.) until the setting is changed. The
bass frequency and bass band width settings adjusted for one
source are effective for all other sources (FM, AM, XM, CD etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, bass level is still adjustable if an
audio processor with the bass adjustment is connected.
• This function is inoperable when DEFEAT is set to ON.
2
* Selecting any of the "Setting the Bass Type" (TYPE 1 through 3),
temporarily replaces the custom settings you have made above.

Setting the Treble Control (CDA-9811 only)

You can change the Treble Frequency emphasis to create your own
tonal preference.
1
Press CENTER f to select the Treble (treble center
frequency) Control mode.
BASS → TREBLE → normal mode → BASS
2-1
Setting the treble Center frequency:
Press g or f to select the desired treble
center frequency.
10.0kHz ↔ 12.5kHz ↔ 15.0kHz ↔ 17.5kHz ↔ 10.0kHz
The displayed Treble frequency is emphasized.
2-2
Setting the treble level:
Turn the Rotary encoder to select the desired
treble level (–7~+7).
You can emphasize the treble frequency.
• If no buttons are pressed within 15 seconds, the treble control
setting will be turned off automatically.
• The treble level settings will be individually memorized for each
source (FM, AM, XM, CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for
all other sources (FM, AM, XM, CD, etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, treble level is still adjustable if
an audio processor with the treble adjustment is connected.
• This function is inoperable when DEFEAT is set to ON.
→(Wide)
13
-EN