Page 1
SERVICE MANUAL FM/MW/LW/RDS CD Receiver TILT 3 / 04-A 68E36337S01 CDA-9831R...
Page 2
<Cautions for Safe Repair Work> The following cautions will prevent accidents in the workplace and will ensure safe products. *The symbols indicate caution is needed to prevent injuries and damage to property. The symbols and their meanings follow. If you ignore this symbol and handle the product incorrectly or unsafely, Warning serious injury or death may result.
CDA-9831R Packing Assembly Parts List Symbol Description Symbol Description Part No. Part No. 101-1 03S60820Y16 SCR,MCH 5X8 ZN A 15D00529K02 CASE,INNER 101-2 03S60824Y01 SCR,WEV 1.7X4 ZN A 15D01798K03 CARRYING,CASE 101-3 01T04296K01 ISO/JASO ANT ADAPTER 01T75411Y01 ASSY,WIRE-ISO-M9831R 101-4 36A02449K01 CAP,RUBBER(A) 68P04190K04...
Page 8
CDA-9831R (3) Control Settings Power Switch ..........ON Band Switch ......FM/MW/LW Fader Control ......Center Position T-CORR ........Non Effect Balance Control ....... Center Position ............FLAT Treble Control ......Center Position DEMO ........... OFF Bass Contro ......Center Position Others ...........
Page 9
CDA-9831R Test Point / Step Description Connection Signal Generator Dial Control P .W.Board Adjustment Coordinates TP012 Auto Adjustment : 216kHz , (3-F) After setting up of Signal Genarator, 34dBµ 216kHz TP011 short GND and TP011 (Pull-Down) (Mod. OFF) (3-F) for 2~3 seconds.
Page 10
CDA-9831R Test Point / Step Description Connection Signal Generator Dial Control P .W.Board Adjustment Coordinates Set up of Adjustment Mode : — — — Push SOURCE/POWER + UP at the same time 98.1MHz, Rotary encoder is turned and noise level...
Page 33
CDA-9831R Description of IC Terminal D78F4216AGC : IC001 Symbol Terminal Description IF MUTE IF MUTE control terminal. (H:IF MUTE ON) No connect terminal. RDS data input prevention control terminal of adjoining station. RDS-CONT (H:RDS OFF) IF MUTE(NC) No connect terminal.
Page 34
CDA-9831R Symbol Terminal Description MARKET1 Area set up terminal. MARKET2 MARKET3 AUTOADJ Auto adjustment start signal terminal of FM/AM TUNER. (L:start) No connect terminal. GND terminal. No connect terminal. Power supply terminal. No connect terminal. PAUSE Audio signal detect terminal. (L:Blank) DAVN Data available input terminal of RDS Decoder.
Page 35
CDA-9831R Symbol Terminal Description F-STBY Active stand-by output signal input terminal from MAIN u-COM. SEARCH AMBER Control signal output terminal for SEARCH KEY lighting LED. (AMBER) LCD INH INH signal output terminal of LCD Driver. F-IN Frame input terminal. F-OUT Frame output terminal.
Page 36
CDA-9831R Symbol Terminal Description BUS-IN Ai-NET BUS signal input terminal. CD RST System RESET output terminal to CD u-COM. CD STBY Active stand-by request signal output terminal to CD u-COM. No connect terminal. BUS IN Ai-NET BUS signal input terminal.
Page 37
CDA-9831R Symbol Terminal Description CD FOUT Frame output terminal. REG RESET RESET signal output terminal to system Regulator IC. RDS RESET RESET control signal output terminal to RDS u-COM. T-MUTE A-MUTE signal input terminal from RDS u-COM. RDS FOUT DATA output signal output terminal to RDS u-COM.
Page 38
CDA-9831R TMS320DA150PGE160 : IC101 Symbol Terminal Description CVSS GND connect terminal. External program address terminal. CVSS GND connect terminal. DVDD Power supply terminal. (+3.3V) External program address terminal. Load-Motor2 LOAD motor control terminal. External program address terminal. CVDD Power supply terminal. (+1.6V) HAS(PULL-DOWN) Pull-down connect terminal.
Page 39
CDA-9831R Symbol Terminal Description SSEL BCLK output signal terminal. PF-BUS2 communication SCK signal terminal. CVSS GND connect terminal. (+1.6V) HINT(PULL-DOWN) Pull-down connect terminal. CVDD Power supply terminal. (+1.6V) MSEL LRCLK output signal terminal. (LR polarity, SMCK fixation) EPF-BUS2 communication CS signal terminal.
Page 40
CDA-9831R Symbol Terminal Description X1(NC) No connect terminal. Clock connect terminal. DSP RESET EPF-BUS2 communication RESET signal terminal. I/O External program data terminal. External program address terminal. DVSS GND connect terminal. External program address terminal. CVSS GND connect terminal. DVDD Power supply terminal.
Page 41
CDA-9831R Exploded View (Cabinet) (1/2) RCA201 SW405 CH701 CH401 LCD401 ANT001 8 X2 JK201 CB801 DIN801 M802 JK601 SW603 SW602 CH511 NOTE : The place of the connection of (L) as shown in ( ), is mentioned in the "Exploded View (Cabinet) (2/2)."...
Page 42
CDA-9831R Exploded View (Cabinet) (2/2) CH831 117 X2 M831 NOTE : The place of the connection of (L) as shown in ( ), is mentioned in the "Exploded View (Cabinet) (1/2)." ..point of GREASE applied. GREASE,E-PAST ( 11S42419J09 ) GREASE,G-8007 ( 11S41558Y01 )
CDA-9831R Electrical Parts List * Each parts on P.W.Board are described in order of the reference number. =======MAIN P.W.Board BZ601 50T15447Y02 BUZZER,PKM13EPY -R5 C007 08S45676W80 CAP,CER 223K-B1E -CP C010 08S45676W85 CAP,CER 104K-B1C -CP C011 08S45676W89 CAP,CER 473K-B1E -CP C012 08S45677W60...
Page 68
CDA-9831R Cabinet Assembly Parts List NOTE : The part that has not PART NUMBER will not be supplied. 01V74700Y97 ASSY,NOSE UNIT 31RT - - - - - - - - - - - COVER,TOP - - - - - - - - - - -...
Page 70
CDA-9831R CD Deck Mechanism Assembly Parts List NOTE : The part that has not PART NUMBER will not be supplied. 01V31800Y79 ASSY,ARM GUIDE 27C11557Y02 CHASSIS,TOP 45B11564Y02 LEVER,LINK-TOP 45B11595Y02 LEVER DISC(R) 45B11596Y02 LEVER,DISC(L) 41B11613Y16 SPRING,PULL 15D50248Y02 GUIDE,TOP-DPS2 07C50608Y01 BKT,MOTOR LOAD-P 03S40014G07...
Need help?
Do you have a question about the CDA-9831R and is the answer not in the manual?
Questions and answers