Bunn DUAL TF DBC Installation & Operating Manual

With smart funnel
Hide thumbs Also See for DUAL TF DBC:

Advertisement

DUAL
TF DBC
®
®
WITH SMART FUNNEL
®
S/N DUAL068000 & UP
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601
FAX: (217) 529-6644
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit
the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain
the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain
a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.
35058.0002C
5/12 ©2010 Bunn-O-Matic Corporation

Advertisement

Table of Contents
loading

Summary of Contents for Bunn DUAL TF DBC

  • Page 1 To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a paper copy of the required Illustrated Parts Catalog mailed via U.S.
  • Page 2 AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.
  • Page 3: User Notices

    USER NOTICES The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels. 00658.0000 00831.0000 As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state 03408.0004...
  • Page 4 USER NOTICES (cont.) Authorized service personnel only. To reduce the risk of electric shock, Disconnect power before servicing. do not remove or open cover. No user-serviceable parts inside. 37881.0002 ELECTRICAL REQUIREMENTS (Models with power cord) WARNING - The brewer must be disconnected from the power source until specified in Initial Set-Up. Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.
  • Page 5: Electrical Hook-Up

    ELECTRICAL REQUIREMENTS (cont.) L2 RED L2 RED 200 or L1 BLACK 230V WHITE WHITE NEUTRAL NEUTRAL L2 RED L1 BLACK L1 BLACK GREEN GREEN GREEN GREEN 200 and 230 volt ac 120/208 and 120/240 volt ac single phase, 60 Hz models single phase, 60 Hz models Note: This electrical service Note: This electrical service consists...
  • Page 6: Plumbing Requirements

    " water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow.
  • Page 7: Operating Controls

    These are used to "receive" information from the Smart Funnel handle (coffee name and batch size), and also from RECIPE CARDS. (j) SCROLL BACKWARDS The upper left corner of the B in BUNN can be used to scroll backwards through the function list. Page 7 35058.2 022410...
  • Page 8: Initial Setup

    Set Brew Volumes section of the Pro- gramming Manual on the Bunn-O-Matic website, at www. bunn.com should the volume need to be increased or decreased. 7. The brewer is now ready for use in accordance with the coffee brewing instructions.
  • Page 9: Coffee Brewing

    SCREEN. COFFEE BREWING 1. Insert a BUNN filter into the Smart Funnel. 2. If a grinder is not used to obtain the coffee grounds, pour the proper amount of fresh coffee grounds into the funnel and level by gently shaking. Slide the funnel into the funnel rails and select batch size. Proceed to step 5.
  • Page 10 7. Reassemble sprayheads and reattach. Sprayheads only needs to be hand tightened. Refer to Programming Manual on the Bunn-O-Matic website, at www.bunn.com for calibration routine to verify sprayhead flow rate matches programmed flow rate. Machine may need to be re-calibrated due to lime build up.

Table of Contents