Electrostatic Discharge (Esd) Precautions; Introduction; Applications; General - Bryant 345MAV Installation, Start-Up, And Operating Instructions Manual

BLOWER SHELF
CONDENSATE
TRAP (INSIDE)
ALTERNATE DRAIN
TUBE LOCATION
CONDENSATE TRAP
DRAIN TUBE LOCATION
UPFLOW APPLICATIONS

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

CAUTION: Electrostatic discharge can affect electronic
components. Take precautions during furnace installation
and servicing to protect the furnace electronic control.
Precautions will prevent electrostatic discharges from
personnel and hand tools which are held during the
procedure. These precautions will help to avoid exposing
the control to electrostatic discharge by putting the
furnace, the control, and the person at the same electro-
static potential.
1. Disconnect all power to the furnace. Multiple disconnects
may be required. DO NOT TOUCH THE CONTROL OR
ANY WIRE CONNECTED TO THE CONTROL PRIOR
TO DISCHARGING YOUR BODY'S ELECTROSTATIC
CHARGE TO GROUND.
2. Firmly touch a clean, unpainted, metal surface of the
furnace chassis which is close to the control. Tools held in
a person's hand during grounding will be satisfactorily
discharged.
3. After touching the chassis, you may proceed to service the
control or connecting wires as long as you do nothing that
recharges your body with static electricity (for example; DO
NOT move or shuffle your feet, DO NOT touch un-
grounded objects, etc.).
4. If you touch ungrounded objects (recharge your body with
static electricity), firmly touch metal surface again before
touching control or wires.
FURNACE
CONDENSATE
DOOR
TRAP
FURNACE
1 4
FIELD 26
DRAIN
CONN
SIDE VIEW
DOWNFLOW AND ALTERNATE
EXTERNAL UPFLOW APPLICATIONS
SLOT FOR SCREW
HORIZONTAL
APPLICATION
(OPTIONAL)
1 2
1
3 4
1 8
7
3 4
1
7 8
WIRE TIE
GUIDES
(WHEN USED)
FRONT VIEW SIDE VIEW
Fig. 5—Condensate Trap
—5—
FURNACE
DOOR
SIDE
7 8
4
1 2
FIELD
1
DRAIN
CONN
FRONT VIEW END VIEW
1
⁄ OD
4
COLLECTOR BOX TO
TRAP RELIEF PORT
1
⁄ OD
2
INDUCER HOUSING
DRAIN CONNECTION
5 ⁄ OD
8
COLLECTOR BOX
DRAIN CONNECTION
SCREW HOLE FOR
UPFLOW OR DOWN-
FLOW APPLICATIONS
(OPTIONAL)
1 4
2 1
⁄ -IN. PVC OR CPVC
2
5. Use this procedure for installed and uninstalled (un-
grounded) furnaces.
6. Before removing a new control from its container, dis-
charge your body's electrostatic charge to ground to protect
the control from damage. If the control is to be installed in
a furnace, follow items 1 through 5 before bringing the
control or yourself into contact with the furnace. Put all
used AND new controls into containers before touching
ungrounded objects.
7. An ESD service kit (available from commercial sources)
may also be used to prevent ESD damage.

INTRODUCTION

The model 345MAV 4-way multipoise, Gas-Fired, Category IV,
condensing furnaces are available in model sizes ranging in gas
input rates of 40,000 to 120,000 Btuh.
For accessory installation details, refer to applicable installation
literature.

APPLICATIONS

CAUTION: Local codes may require a drain pan under
entire furnace and condensate trap when a condensing
furnace is used in an attic application or over a finished
ceiling. Failure to follow this caution will result in minor
property damage.
I. GENERAL
Some assembly and modifications are required for furnaces
installed in any of the 4 applications shown in Fig. 1. All drain and
pressure tubes are connected as shown in Fig. 6. See appropriate
application instructions for these procedures.
FURNACE
SIDE
4
3 4 3 4
5 5
4
1 4
26
3 4
FRONT VIEW
HORIZONTAL
APPLICATIONS
A93026