Table of Contents
Advertisement
Model D2424LVmkII Reference Manual (Changing the Initial Settings <SETUP mode>)
Setting the Record Protect function
The recorder features the Record Protect function,
which is similar to the function of record-protect
tabs on cassette tapes. The "Setting the Record Protect
function" menu allows you to turn the Record Protect
function on and off.
When this function is turned on, you cannot record,
paste, or erase data. Use this function to protect your
precious data from being erased accidentally.
• Initial setting:
• Option:
* You can turn the function on and off for each Program
individually.
* The settings can be saved and loaded as part of the
song data.
* The settings are maintained after you turn off the
power to the recorder.
* The Program is automatically checked before the
operation.
(1)
While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
(2)
Turn the Jog dial to select "Rec Protect ?" ("?"
flashes), then press the [EXECUTE/YES] key.
The current setting appears on the display.
Pressing the [EXECUTE/YES] key turns off the
flashing "?" character, and the recording enabled/
disabled indicator flashes. With the initial setting,
"Off" flashes as shown below.
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
4
5
6
7
8
9
3
(3)
Use the Jog dial to enable or disable recording.
Rotating the Jog dial clockwise and counter-
clockwise will flash "On" and "Off" alternately.
Selecting "Off" enables recording; you can record,
paste, and erase data.
Selecting "On" disables recording; and you cannot
record, paste, or erase data.
<Note>:
When recording is disabled (On) and
you try to record, paste, or erase data, the
recorder displays "Protected" for a second,
indicating that you cannot perform the
operation. To perform the operation, you need
to enable recording (Off).
(4)
Press the [EXECUTE/YES] key.
To cancel the setting operation, or to exit SETUP
mode after storing data, press the [STOP] button
or the [EXIT/NO] key. Each time you press one of
these keys, the recorder returns to the previous
hierarchy level of the menu, and finally exits
SETUP mode.
[Off]
[Off] or [On]
OL
BIT
24
0
3
6
9
12
18
CLOCK
24
INT
30
42
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Flashing
OL
BIT
24
0
3
6
9
12
CLOCK
18
24
INT
30
42
21
24
10
11
12
13
14
15
16
17
18
19
20
22
23
In the "Setting a digital input" menu, the signal to be
input to the [DATA INPUT] connector of the recorder
can be set for either digital signals (adat digital signal
or S/P DIF digital signal) or analog signals, and also
setup of the digital in clock (synchronous or
asynchronous).
By using this function, signals from external digital
equipment (CD, MD, DAT, adat digital mixer) can
be digitally recorded.
When selecting the clock, there are the "Async" and
"Sync" modes; either should be selected depending
on the application. If it is set to "Async" mode, the
later explained "Clock Sel?" (Setting the operating
clock) should be setup in accordance to the
application.
• Initial setting:
• Assignable digital signal/setting digital in-clock:
[adat: Async], [adat: Sync], [SPDIF: Async], [SPDIF: Sync],
[Analog]
* This setting is shared by all Programs in the same
disk.
* The settings cannot be saved and loaded as part of
the song data.
* The settings are maintained after you turn off the
power to the recorder.
<Function of the [DATA INPUT] connectors>
<Setup for analog signals>
If the digital input is set up for Analog (Initial setting),
digital signals cannot be input at [DATA INPUT] 1-8, 9-16
and 17-24 of the D2424LVmkII.
<Setup for S/P DIF digital signals>
FS
kHz
If the digital input is set up for S/P DIF (Async or Sync),
only [DATA INPUT] 1-8 can be used. S/P DIF digital sig-
nals input to [DATA INPUT] 1-8 will be assigned and re-
corded in tracks 1 and 2 of D2424LVmkII.
<Setup for adat digital signals>
If the digital input is set up for adat (Async or Sync), all
[DATA INPUT] connectors can be used.
FS
Adat digital signals input to [DATA INPUT] 1-8 will be
kHz
assigned and recorded in tracks 1-8; the signals to [DATA
INPUT] 9-16 in tracks 9-16; and the signals to [DATA IN-
PUT] 17-24 in tracks 17-24.
Note: The [DATA INPUT] connectors do not support 96kHz
FS adat digital signals.
(1)
While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
(2)
Turn the Jog dial to select "D. in ?" ("?" flashes),
then press the [EXECUTE/YES] key.
When "D. in?" ("?" flashes) is selected, the presently
set digital input content will be shown.
The flashing "?" is extinguished when the [EXECUTE/
YES] key is pressed and the digital input setting
will change from lighting to flashing.
In the initial setting, "Analog" will flash as shown
below.
117
Setting digital input
[Analog]
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
OL
BIT
24
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
20
21
22
23
24
Advertisement
Chapters
Table of Contents
