Table of Contents
Advertisement
Model D2424LVmkII Reference Manual (Changing the Initial Settings <SETUP mode>)
Time Signature Setting
Using the "Setting a time signature" menu, you can
set a time signature of a given measure on the
internal programmable Tempo Map. And also in
this setting, the BAR (-002bar, 1 , 00clk) displayed
at the head of the disk in the time base BAR/BEAT/
CLK can be set within the range of -009bar ~ -002bar.
For example, you can specify "4/4 for the first and
second measures, and 2/2 from the third measure."
Setting a time signature and tempo will create a
Tempo Map, which allows the recorder to manage a
song using the BAR/BEAT/CLK Time Base. You can
also use the Metronome function.
A time signature and tempo setting are required
when MIDI clock & song position pointer are output
to an external sequencer.
• Initial Setting
• Available bars
• Available time signature : 1/4, 2/4, 3/4, 4/4, 5/4, 1/8, 3/8, 5/8,
• Maximum setting points: 64
* The setting is applicable song by song.
* The setting can be saved or loaded as a part of the song
data
* The setting is memorized even when the power is off.
* Make sure you choose the right program before setting this
mode.
Storing a time signature
(1)
Select a Program for which to set a time signature.
Refer to "Using the Program Change function" on page
"37" for information on selecting a Program.
(2)
Press the [SETUP] key, use the Jog dial to select
the "Signature.Set ?" menu, then press the
[EXECUTE/YES] key.
The indication changes to the current time signature
appears. The initial setting is "001bar 4/4 " (4/4 for
the first measure).
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
SETUP
OL
0
3
6
9
12
18
24
30
42
1
4
5
6
7
8
9
2
3
At this time, rotating the Jog dial clockwise enables
you to check the current time signatures in
sequence.
With the initial setting, time signatures after the
first measure are all "- - -bar - /- ". This means that
a time signature of 4/4 applies to all measures.
(3)
Press the [EXECUTE/YES] key.
The indication changes to "001 (measure)" of
"001bar 4/4 " flashes. You can enter any time
signature here.
: 001bar 4/4 beat
: 001 ~ 999
6/8, 7/8, 8/8, - -/- - (Delete)
OL
BIT
24
0
3
6
9
12
18
CLOCK
24
INT
30
42
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
OL
BIT
24
0
3
6
9
12
18
CLOCK
24
INT
30
42
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
• Rotate the Jog dial to enter the desired measure
number.
If you wish to keep the initial setting for the first
measure, enter 002. If you try to enter any number
other than 001, the time signature indicator shows
"-/- ". This means that no time signature is set for
any measures other than the first measure.
To change the time signature for the first measure,
follow the steps below, without entering any other
measure number.
• Turn the Shuttle dial to display flashing "-/-" of
"-/- " and enter the time signature using the Jog
dial.
The following measure numbers and time signatures
can be entered via the Jog dial.
Measures
signatures
<Note>
You cannot assign "- - -" to measure 001.
(4)
Press the [EXECUTE/YES] key whenever you enter
a pair of measure/time signature values.
Repeat this step to specify the necessary time
signature for the measures.
To cancel the setting operation, or to exit SETUP
mode after storing data, press the [STOP] button
or the [EXIT/NO] key. Each time you press one of
FS
these keys, the recorder returns to the previous
kHz
hierarchy level of the menu, and finally exits
SETUP mode.
Modifying (or deleting) stored time signatures
FS
kHz
(1)
Repeat steps 1-3 described in the "Storing a time
signature" section.
(2)
Turn the Shuttle dial so that the flashing cursor is
on the time signature value.
(3)
Use the Jog dial to enter a new value.
Entering "-/-" deletes the existing data. Note that
you cannot enter "-/-" for measure 001.
(4)
Press the [EXECUTE/YES] key.
(5)
Press the [EXIT/NO] key (or [STOP] button).
110
Flashing
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
001-999, selection of [All Clear?]
indication.
[All Clear?] means that data in its
entirety will be cleared. This is used
to initialize the parameter. (Refer to
"Clearing stored time signature/tempo
data.")
1/4, 2/4, 3/4, 4/4, 5/4, 1/8, 3/8, 5/8,
6/8, 7/8, 8/8, -/-
Time
[-/-] means no time signature assigned,
and is used to delete time signature
data. (Refer to "Modifying (or deleting)
stored time signatures" for more
information.)
OL
BIT
24
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
20
21
22
23
24
Advertisement
Chapters
Table of Contents
