Page 1
wner peratOr anual The Choice of Experience Odels CC34 rOCessOrs Noticia importaNte importaNt Notice este manual contiene importantes instrucciones this manual contains important Safety de seguridad que deben ser seguidas el pie de la instructions which must be strictly letra cuando utilice esta maquina. followed when using this equipment.
INGS RELATED TO YOUR PERSONAL SAFETY ARE INDICATED if any warning label, wall chart or manual becomes misplaced, damaged or illegible, please contact your nearest distributor or Berkel directly, for a free replacement. remember, however, THIS MANUAL OR THE WARNING LABELS DO NOT REPLACE THE NEED TO BE ALERT AND TO USE YOUR COMMON SENSE WHEN USING THIS FOOD PROCESSOR.
UtiLiZe UNicameNte los repuestos provistos por el fabricante. eN caSo de que los membretes de ‘peLiGro’ se desprendan de la mçquina o sean illegibles, llame al fabricante o a su representante de service Berkel para que lo reemplace sin cargo. eneral...
qUipmenT esCripTion Variable Speed Feed Tube Shaft Control Feeder Handle Large Feed Compartment Machine Outlet Machine Handle Base Pusher Standard Slicer Scraper Handle Crimping Slicer Fine Cut Slicer Julienne Cutter Scraper Ring Dicing Grid Knife Grater/Shredder Bowl Fine Grater Ejector Plate –...
Page 6
Always Use Ejector Plate Assemble Sealing Ring Into Lid Dismantling Lid When Dicing - Sharp Edge Up Dismantling Scraper Assembling Lid Dismantling Feeder Unit Assembling Bowl Assembling Feeder Unit Assembling Scraper Assembling Knife Wall Racks – 6 –...
nTended ses and haraCTerisTiCs Intended Uses the models cc34, c32 and B32 Food processors are designed for the following applications: • Slices, dices, shreds and/or grates fruits, vegetables, dry bread, cheese and nuts. • Chops and grinds meat, fish, fruits, vegetables and nuts. •...
To eliminate a potential shock hazard, a properly grounded outlet using the three- pronged plug provided must power this unit. Before plugging the food processor in, check your outlet voltage to be sure it complies with the voltage specified on the serial number plate on the food processor.
Page 9
Choice of Cutting Tools When Processing With the Feeder: Slicer: Slices soft and firm foods. Dices in combination with the Dicing Grid. crimping Slicer: For ripple slicing. Julienne cutter: For julienne potatoes, cucumber, etc. 3/16 x 3/16 in. (4.5 x 4.5 mm) for shred- ding of white cabbage.
Page 10
Amount, Size and Processing Times of Foods, When Processing With the Bowl: the amount and size of the pieces which can be processed at one time, and the length of time the processing takes, depend on the consistency of the foods and on the result desired. For even and consistent results with firm foods such as meat and cheese, it should first be sepa- rated into pieces approximately equal in size and not bigger than 1x1x1 in.
With the variable speed control in the “o” position, the machine is switched off. in the “i” posi- tion, the machine operates continuously at low speed. in the “ii” position, the machine operates continuously at high speed. in the “p” (pulse) position, the machine operates at high speed until the variable speed control is released.
check the circuit breaker in the electrical panel to see if it has tripped. check that the feeder is correctly installed and that the feeder handle has been lowered. check that the bowl and lid are correctly installed. Wait for up to 30 minutes and then try to start the machine again. call in a service technician for further action.
Page 13
Users: restaurants, dietary kitchens, day care centers, retirement homes, catering establishments, etc. preparing from 10 to 80 portions a day. Capacity and Volume: processes up to 4 lbs. per minute with the feeder depending on the type of cutting tool and prod- uct.
Page 14
Cutting Tools and Chopping Knife: the diameter of the cutting tools is 7.25 in. the diameter of the chopping knife is 6.70 in. Materials: the machine base is made of aluminium. the continuous feed attachment: • Housing: Polycarbonate • ejector plate: acetal •...
These warranties are given only to the first purchaser from a Berkel Authorized Channel of Distribution. No warranty is given to subsequent transferees.